Channel Problem after Firmware Update + Subtitles?

Started by Keith, February 16, 2023, 03:29:22 PM

Previous topic - Next topic

Ian_AW

Quote from: Keith on February 18, 2023, 05:59:12 PMI wrote down the IP address when doing the firmware update.
I've just looked again under System Information and the IP address is blank, no address is displayed

My reason for asking was to try and flush out where it was getting to. So, at least you know where in the boot cycle the system is getting to rather than try and look everywhere.

Hopefully the fix will be there soon for you.

vader1111

Quote from: Keith on February 18, 2023, 11:01:57 AMUnfortunately the soft reset has not fixed my issue.
My TV tab is blank and when OK is entered an endless "PVR manager is starting up" loop appears.
IceBox has also disappeared from my Add-ons.
Pics attached...
Keith, this sounds like the very first version of the firmware, which the beta testers received last November.  We haven't seen anything like what you're describing for a long time.

Can you confirm which version of the firmware you are running?

Keith

The firmware version appears to be current. Pic attached

IanL-S

Keith, I just remebered why this may be happening. I had this problem early on during beta testing. My solution was to my IceTV account, then select My Recorders, then I clicked on the Add Recorder tab and created a dummy device in my IceTV account settings; in my case a TRF-2460 which I gave the name "Dummy". I then selected the the Copy Timers to a new device tab, and copied the timers from the IceBox to Dummy. This only copies timers for series recordings; one of timers will not be copied.

The next step was to go back to My Devices tab, and delete the IceBox device.

When the IceBox next contact the server, a new device is created, called Ice Box, and hopefully the installation wizard will go to completion. You must power off the IceBox before making the account chnages. The start the IceBox and the Installation Wizard may run of its own volition, if not you will need to do a soft reset to initiate the wizard.

Hope this solves your problem.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Keith

My IceTV account is currently set up to record identically onto 2 devices - my old Beyonwiz T2 and the IceBox.
 
Could I just power off the Icebox and delete it from IceTV rather than creating a dummy device? I assume the Beyonwiz recording instructions would then copy to the IceBox if installation succeeds.

Thanks to all for your advice :)

IanL-S

You would have to manually copy the timers to the IceBox using the method I described above.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Daniel Hall at IceTV

Hi Keith,

This sounds like the the network was not setup correctly during the initial setup wizard, there are updates that are required just after the initial setup wizard is complete and this has not happened.

To fix this now the best option is to perform another 'soft reset' and then during the initial setup wizard ensure that the network gets connected and shows as "State: online" and that the "Address" shows an IP Address.
Regards,

Daniel.
CTO.

Keith

Thanks Daniel and IanL-S,

I first did the soft reset as suggested by Daniel and obtained an online state and IP address. IceBox also reappeared in my add ons and I was able to go through the IceTV setup and channel scan. As before the channel scan resulted in zero channels.

I then powered off the IceBox and deleted it from my IceTV recorders list as suggested by IanL-S. Restarting the IceBox initiated a new channel scan which again resulted in no channels found. The IceBox did not show up in my IceTV devices and could not be manually added as it is automatic through the device.

Next was another soft reset, online state and IP address obtained, IceTV account details correctly entered, channels scanned and again no channels located. The log continues to show the same error message as on previous occasions: Tvheadend HTSP Client server is unreachable. At least the IceBox does now show up in my IceTV devices.

I have checked the physical connections for the tuners, which have not been touched since installation, and they appear to be properly connected.

Is there anything else I can try to get this unit working?

Daniel Hall at IceTV

Quote from: Keith on February 19, 2023, 10:03:59 PMI first did the soft reset as suggested by Daniel and obtained an online state and IP address. IceBox also reappeared in my add ons and I was able to go through the IceTV setup and channel scan. As before the channel scan resulted in zero channels.

This is the most concerning part to be honest, are you able to take a photo of your tuners and the splitter to show how it all looks so we can see it?
Regards,

Daniel.
CTO.

Ian_AW

I apologise for asking this, but here goes. Is everything plugged in properly?

IanL-S

Quote from: Ian_AW on February 19, 2023, 10:33:19 PMI apologise for asking this, but here goes. Is everything plugged in properly?

It appears that everything was checked from the information provided; need to make sure that the coax cable is fimrly attached to the tuners and a splitter if there are 2 USB tuners. Also check the F-type male to PAL male connectors are firmly screwed onto the spliter; that the coax from the wall plate to the splitter is firmly seated.

All my wall-plates have f-type connections; one time I had a cable come loose and did not notice it had happened. You do not expect f-type connections to unscrew.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Keith

Thanks Ian_AW and IanL-S. No apologies required as you have solved my problems :)

I had checked the IceBox connectors and cables including the splitter, but not the wall plate PAL outlet. With diabolical timing the coax cable was loose at the wall. It's near a power point and probably got knocked. I'll have to look at changing to F-type connectors on my wall plates.

With everything properly connected, IceBox found all my channels and I could copy the timers from my Beyonwiz.

With much embarassment, thanks to everyone for your advice.






MD

That's excellent news and thanks for the update (and admission🤣👍).

IanL-S

Wow, glad it is sorted after all this time.

You are not the first and will not be the last be caught by loose connection at the wall plate.

Now all I need to do is to work out why my "new" build-your-own unit is having similar problems.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

MD

Just one more thing... Ian mentioned a loose F-Type connector which possible "unscrewed" due to a slight twist in its cable (guessing here?!).  Yet they need to be just "pinch tight" as the steel "nut" is tightening on to a cast alloy thread and they can get over tightened very easily when the thread strips or the nut becomes misaligned. Personally I find finger tight is satisfactory as there's no reason for them to ever shake loose, but ensure cables are not twisted to turn them undone again.  If a spanner or pliers are used be very gentle.