Setting end padding to 15 minutes

Started by Ian_AW, January 27, 2023, 08:51:50 PM

Previous topic - Next topic

IanL-S

OK understand what you are getting at now. When Daniel created the ability to request timer/EPG download he located it in the IceTV configuration. It is independent of all the other things that are there - you just select the update EPG the click on OK. This is completely independent from the other things found there.
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Ian_AW

The reason I linked the add on to changing the setting in TVHeadEnd was because information to access TVHeadEnd  was asked for.

The IP is the IceBox IP address, the port is 9981, and somewhere I recall being told to ignore any request for a TVHeadEnd username and password.

IanL-S

Thanks for the explanation.

You only need a user name and password for TVheadend www portal if you set up a user name and password previously. That may be considered prudent as there is a (relatvely small) risk someone could break into the IceBox via the TVheadend www page.
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

IanL-S

That is what you should see. Move to the first item Force EPG update, then move to OK and press OK and it will happen. The stuff below is irrelevant to Force EPG Update.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

IanL-S

#19
Quote from: IanL-S on February 16, 2023, 10:50:17 AMYou can change the default in TVHeadend (could have changed in the last week).

You log into TVheadend: http://{IP address of IceBox):9981/

Select the Configuration tab; the click on the Recording tab, then select the IceTV profile in the left colum. Chnage the values for pre and post pading, and click the Save button (fourth row from the Top, leftmost tab).

The new padding only applies to timers sent to the IceBox after they were changed.

Hope this helps

Ian

Hope this helps.

It no longer works like this; there is no loger an ability to select a profile. It is possible that the only profile presented is the one that works for IceTV. I will test and report back. Looks like the default is now being set in the Kodi Settings for PVR/TV where under recordings the 3/30 values are found.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Ian_AW

Quote from: IanL-S on February 18, 2023, 12:56:57 PMIt no longer works like this; there is no loger an ability to select a profile. It is possible that the only profile presented is the one that works for IceTV. I will test and report back. Looks like the default is now being set in the Kodi Settings for PVR/TV where under recordings the 3/30 values are found.

Ian

Does this mean that while a different value can be set in PVR/TV, when IceTV sends timers, they will have the padding set to 3/30?

IanL-S

Quote from: Ian_AW on February 18, 2023, 01:35:30 PMDoes this mean that while a different value can be set in PVR/TV, when IceTV sends timers, they will have the padding set to 3/30?

The value set in PVR/TV is used for timers set by IceTV (initially 3/30). If you change that setting, fore exmple to 15/30, then the 15/30 padding only apply to new timers downloaded after that setting is changed.

This behaviour may change in the future, but it is what happens at the moment.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help