My IceBox is not setting recurring timers past January 26, 2023.
I went hunting through the settings and found an entry on the PVR-TV screen which stopped the IceBox from receiving timer updates during playback.
I was also missing recordings being set well over a couple of hours before the event because I was watching a series of recordings in sequence.
I switched that setting OFF to allow updates at all times to see if that released the timers but no luck.
Overnight, there have been no recurring timers reset with it still showing no new timers after January 26, 2023.
Is it possible that the timer involved is blocking new timer events being set, or should I delete the timer in question and see if the IceTV server resets in and those queued up behind?
Thanks.
Can you please go to My Account -> Guide Settings, in the IceTV website, and confirm whether or not your IceBox is still doing EPG fetches?
Beta testing identified a number of conditions which caused the IceBox to stop fetching the EPG data from the IceTV servers. However, these have all been fixed, as far as I am aware, prior to public release. It's possible you've found another one.
Quote from: vader1111 on January 24, 2023, 10:05:44 AMCan you please go to My Account -> Guide Settings, in the IceTV website, and confirm whether or not your IceBox is still doing EPG fetches?
Beta testing identified a number of conditions which caused the IceBox to stop fetching the EPG data from the IceTV servers. However, these have all been fixed, as far as I am aware, prior to public release. It's possible you've found another one.
This is the information from My Account > Guide Settings
So, EPG fetches are OK, just the timers are not getting added.
Last EPG fetches:
24 January, 2023 at 09:46am with IceTV Remote - iPhone
24 January, 2023 at 10:13am with IceTV IceBox
24 January, 2023 at 10:13am with Windows 7 MCE
Thanks.
I have seen this with pre-release beta, but with the exception of Who Do You Think You Are? all timers are downloading.
If you have scheduled Who Do You Think You Are, check to make sure the timer is set, as it has been reported that timers for that program are not being set. I have 5 epsidoes that have not been set to record (4 for Australia and one for USA).
Ian
Quote from: IanL-S on January 24, 2023, 10:56:35 AMI have seen this with pre-release beta, but with the exception of Who Do You Think You Are? all timers are downloading.
If you have scheduled Who Do You Think You Are, check to make sure the timer is set, as it has been reported that timers for that program are not being set. I have 5 epsidoes that have not been set to record (4 for Australia and one for USA).
Ian
The program timer it stalls on in War of the Worlds, however deleting it has not seen it reappear. It is the last in the list (most into the future).
Something is causing it to stall.
At around 10:13 this morning, I did a power down and then power up. This is what I showed in my earlier post.
After 1 hour 15 min on the phone with a problem with my phone service (unrelated - Optus kept telling callers my number had been disconnected), I checked, and nothing had advanced.
I decided to resend all the timers from My Account > My Recorders, but nothing changes. The IceBox does not show any of the stalled timers, and there is nothing new in My Account either.
After lunch, I am going to try and figure out which event is the issue. I might even risk clearing out the timers and get them from IceTV again.
Quote from: raj1954 on January 24, 2023, 12:38:09 PMSomething is causing it to stall.
At around 10:13 this morning, I did a power down and then power up. This is what I showed in my earlier post.
After 1 hour 15 min on the phone with a problem with my phone service (unrelated - Optus kept telling callers my number had been disconnected), I checked, and nothing had advanced.
I decided to resend all the timers from My Account > My Recorders, but nothing changes. The IceBox does not show any of the stalled timers, and there is nothing new in My Account either.
After lunch, I am going to try and figure out which event is the issue. I might even risk clearing out the timers and get them from IceTV again.
Can you confirm that it is still doing EPG fetches? When the IceBox reboots, it attempts to call home, and this shows up as an EPG fetch. Unfortunately, if there is a problem downloading the timers or EPG information, it then stops calling home.
You said that you rebooted at 10:13am, and it's possible that the IceBox fetch shown is this initial EPG fetch attempt. Can you confirm that it is still fetching the EPG, beyond that initial attempt?
Quote from: vader1111 on January 24, 2023, 01:18:31 PMCan you confirm that it is still doing EPG fetches? When the IceBox reboots, it attempts to call home, and this shows up as an EPG fetch. Unfortunately, if there is a problem downloading the timers or EPG information, it then stops calling home.
You said that you rebooted at 10:13am, and it's possible that the IceBox fetch shown is this initial EPG fetch attempt. Can you confirm that it is still fetching the EPG, beyond that initial attempt?
This is the current EPG fetches, and the only one that seems to be re-checking is the Windows 7 MCE which I would guess and say it is the account page of the site. The IceBox is doing nothing, and even the 10:13 am fetch did not link anything past January 26, 2023.
24 January, 2023 at 10:39am with IceTV Remote - iPhone
24 January, 2023 at 01:52pm with Windows 7 MCE
24 January, 2023 at 10:13am with IceTV IceBox
I am going to cycle the router.
Cycled it, but no change.
Last EPG fetches:
24 January, 2023 at 10:39am with IceTV Remote - iPhone
24 January, 2023 at 02:08pm with Windows 7 MCE
24 January, 2023 at 10:13am with IceTV IceBox
Sounds like we are looking at the wrong end of the list. Maybe something has become corrupted and causing the transfer to time out.
Starting to look like the solution is to delete the timers and get IceTV to add them.
Is there a log file somewhere?
Quote from: raj1954 on January 24, 2023, 02:28:57 PMQuote from: vader1111 on January 24, 2023, 01:18:31 PMCan you confirm that it is still doing EPG fetches? When the IceBox reboots, it attempts to call home, and this shows up as an EPG fetch. Unfortunately, if there is a problem downloading the timers or EPG information, it then stops calling home.
You said that you rebooted at 10:13am, and it's possible that the IceBox fetch shown is this initial EPG fetch attempt. Can you confirm that it is still fetching the EPG, beyond that initial attempt?
This is the current EPG fetches, and the only one that seems to be re-checking is the Windows 7 MCE which I would guess and say it is the account page of the site. The IceBox is doing nothing, and even the 10:13 am fetch did not link anything past January 26, 2023.
24 January, 2023 at 10:39am with IceTV Remote - iPhone
24 January, 2023 at 01:52pm with Windows 7 MCE
24 January, 2023 at 10:13am with IceTV IceBox
I am going to cycle the router.
Cycled it, but no change.
Last EPG fetches:
24 January, 2023 at 10:39am with IceTV Remote - iPhone
24 January, 2023 at 02:08pm with Windows 7 MCE
24 January, 2023 at 10:13am with IceTV IceBox
Sounds like we are looking at the wrong end of the list. Maybe something has become corrupted and causing the transfer to time out.
Starting to look like the solution is to delete the timers and get IceTV to add them.
Is there a log file somewhere?
Your IceBox hasn't done an EPG fetch since you rebooted it at 10:13AM. This is what I was expecting to see, given our previous experiences when beta testing. We thought we'd gotten rid of all of these problems, but apparently you've discovered another one!
Rebooting the router won't fix the problem.
Log files can be generated by going to //icebox/Logfiles in File Manager (on a Windows computer, on the same network as the IceBox). Posting it here would be very helpful (it should be a few hundred KB in size).
What you could do, which would be helpful, is this...
1. Delete all of the timers, in IceTV, which are supposed to be going to your IceBox.
2. Reboot the IceBox.
3. Re-add the timers (in IceTV) one, by one, waiting until you have a solid red disc (indicating that the timer has gone through) before proceeding to the next timer.
This would help us to isolate the offending timer, and we can start to figure out why it is causing problems.
Raj - can I ask you where you are located? When we were doing the beta testing, people in Canberra had problems with the IceTV -> Antenna channel mappings, which were significantly different from those in the main capital cities.
If you're in a regional area, then it may be that Dan has some more work to do on the channel mappings for your region.
Hi Ian,
You IceBox is not connecting to our servers. You can always heck by going to your IceTV website Guide Settings where the last login times of each device is show. At present the IceBox should connect every minute, a fast repeat connection we have set to make testing easier.
I'd suggest a hard reset from within the LibreELEC icon In System Settings?
Before going to extremes, I would try deleting your IceBox from your account. The procedure I have used in the past:
- Create a dummy device in your account (I use Topfield 2400 for device type).
- Chnage the name of the device in your account to Dummy
- Copy the timers from your IceBox to the Dummy device
- Power down the IceBox
- Delete the IceBox from your account
- Start up the IceBox, hopefully it will recreate the device in your account.
- Once you are safisfied that the IceBox is contaction the IceTV server every minute, copy all the times from Dummy to IceBox.
- Hopefully the timers will then be downloaded; because the IceBox is logging in every minute there could be interruptions to the process but eventually all timers should download.
No guarantee that it will solve the problem, but is has worked a few times for me.
Resetting the IceBox should be the last thing you try, as doing so apparently deletes all your recordings.
To help in dealing with the issue, please download the log files using the process described by
vader1111 and post them here.
Hope this helps
Ian
Ok, I deleted all the timers and then rebooted the IceBox.
There was no timer information. In other words, it was like I had just started IceTV from scratch.
I created a timer in the IceTV app. I waited for the next fetch, and nothing. When I create the timer event in the app, the red disc is red.
If I do a send recording events to the device, again, with just one timer, again, nothing.
At the moment it is a case of setting events on almost every day as those that were previously set would have run into the brick wall.
I am going to try and do a transfer of information from my expired Beyonwiz T2.
I will try and upload the log files to support.
Quote from: raj1954 on January 24, 2023, 04:39:56 PMOk, I deleted all the timers and then rebooted the IceBox.
There was no timer information. In other words, it was like I had just started IceTV from scratch.
I created a timer in the IceTV app. I waited for the next fetch, and nothing. When I create the timer event in the app, the red disc is red.
If I do a send recording events to the device, again, with just one timer, again, nothing.
At the moment it is a case of setting events on almost every day as those that were previously set would have run into the brick wall.
I am going to try and do a transfer of information from my expired Beyonwiz T2.
I will try and upload the log files to support.
Can you confirm that your IceBox is doing EPG fetches? It should be doing them every minute, so hitting refresh a few times on the "Guide Settings" page in IceTV should give you an idea whether or not this is happening.
However, it sounds as if a "Hard Reset" may be in order. Note that this formats the SSD, deleting any/all recordings in the process - so make sure you've copied them elsewhere before you nuke the box.
My suggestion...
- Delete all IceBox timers in IceTV
- Hard Reset
- Add timers again, one at a time (as per my previous instructions), until the culprit is revealed
- Upload logfile once the culprit is identified.
To do a Hard Reset, go to Settings, then go down the bottom to LibreELEC settings. Look for an option to reset IceBox to original settings (or words to that effect). Sorry, I'm not at home, so I can't tell you what the actual menu item is.
When doing the Hard Reset, don't forget to wait ~2min at the SSH/SMB page (in the LibreELEC wizard), this gives the IceBox time to find/download/install the latest version of the IceTV Addon before you start the IceTV Wizard.
Well, I had the single event (Jeopardy!) set by picking the record button on the remote. The timer events were empty.
I went to My Account and picked the tab to transfer timers from my old T2 to the IceBox. Now what I was expecting was for the entire lot of timers to come over, however only the remaining events for Jeopardy! for the rest of the EPG period were set right until Jan 30, 2023.
Im hoping that it will be a matter of doing this for the rest of the timer events and then create any additional ones.
Quote from: raj1954 on January 24, 2023, 05:02:27 PMWell, I had the single event (Jeopardy!) set by picking the record button on the remote. The timer events were empty.
I went to My Account and picked the tab to transfer timers from my old T2 to the IceBox. Now what I was expecting was for the entire lot of timers to come over, however only the remaining events for Jeopardy! for the rest of the EPG period were set right until Jan 30, 2023.
Im hoping that it will be a matter of doing this for the rest of the timer events and then create any additional ones.
That's a different story. Timers created locally on the IceBox are not currently reflected back to your IceTV account - it's on the "To Do" list.
However, the "Copy timers to a new recorder" function (IceTV -> My Recorders page) should copy any/all timers which were created in IceTV (phone app or website).
Not having much luck. After the first timers for one event went perfectly, however the next two I tried added nothing,
Before I do a hard reset, I have to preserve some of the programs I have recorded.
How do I attach the log files to messages in the forum?
Ok, might need some patience and reboot at the end. I've generally had a bad day. Got a call from a client this morning that when he called me on my fixed line service, he got a message from Optus that my service had been deleted.
After an hour and a half waiting in a queue at Vonex it turned out that all their customers were being told that by Optus! That is sorted not. Then trying to get this working. I am not keen on rebooting each time.
One way to post a log file is to generate a support ticket and copy it to the ticket. To get the log file find the IceBox via your PC/Mac on your home network where you'll see it has a list of folders, one of which is "logfile". Within that folder is the file you need.
Remember - every time you do a reset the old file and its information is deleted so the file will only contain info from there on which may or may not be useful.
I will send the logs through when things were not working.
I decided to take a break and let things be for a while.
I had tried to copy my timers over from the configuration of my T2, and had power cycled the IceBox so had my tea and then decided to have a further attempt at getting things working and to my surprise say all the timers copied over and looking ahead until January 30.
So, whatever has happened seems to have fixed things. Some new timers will reveal themselves as time goes by.
Thanks to all who offered tips. Everything crossed that it all stays as it should.
Now to send the log file :D
Raj - can you confirm that you applied the GZ image Update when you first installed the IceBox? I believe you were sent an email with instructions for doing this.
The problems you are experiencing sound very much like the ones we had during beta testing, and which were fixed with a firmware release last weekend - after the initial batch of IceBoxes had been sent in the mail.
Quote from: vader1111 on January 25, 2023, 09:59:04 AMRaj - can you confirm that you applied the GZ image Update when you first installed the IceBox? I believe you were sent an email with instructions for doing this.
The problems you are experiencing sound very much like the ones we had during beta testing, and which were fixed with a firmware release last weekend - after the initial batch of IceBoxes had been sent in the mail.
I believe so.
I received a call from Colin and went through a hard reset which involved basically going through the first-time startup with the updated firmware that was uploaded remotely.
Ok, after having things working for the best part of a day, I remembered I had not set the repeat flag, so at around 4:24 today I decided to set it and it looks like the problem is back. I have the EPG and timers update every 15 minutes, however since making that change, this is the latest fetch report. It is now 5:56 pm, so there should have been at least 5 updates.
Last EPG fetches:
25 January, 2023 at 04:18pm with IceTV Remote - iPhone
25 January, 2023 at 05:39pm with Windows 7 MCE
25 January, 2023 at 04:24pm with IceTV IceBox
I now have to wait for a beak in what I am recording and do a hard shutdown and restart and see it that clears it. Failing that I will delete all timers and reimport them from my Beyonwiz device.
For what it's worth, I had set the repeat flag to RPT added to the start of the Description.
I wonder if anyone will be willing to try it :D
I have the repeat flag at the end, and do not recall any issues.
Today I had a problem with stall of logging in; I suspect it was cause by a power outage and assoicated loss of internet connection. Not sure what I did to fix it but eventually started logging in to the server every minute.
Ian
PS If I get a chance I will set up my build your own IceBox tomorrow and see if the repeat tag a the befinning causes any problems.
Quote from: IanL-S on January 25, 2023, 07:16:34 PMI have the repeat flag at the end, and do not recall any issues.
raj1954 says that he has the repeat flag set at the start of the description. Do you have it set on the title (the default field)?
I have it set on title - that is where it turns up. See screenshot. Must admit that I never considered any alternative setting.
OK, just finished a few hours getting my IceBox back up with timers working.
Yes, it has to do with setting the Repeat flag.
If I have the flag to display [Rpt] before or after ANY of the possibilities, the scheduling of new timers will cease, including series timers or individual ones set via the IceTV system or app.
You can still set timers via the Guide (on the IceBox) or by adding a new timer manually (on the IceBox), however if you set timer via the web page or app, it will NOT come through to your IceBox.
If you do not have another device with your timers set in it, when you have the system working properly, you will have to add your timers individually.
To recover things is to delete ALL timers on the IceBox and remove the schedule of timers in My Week. All you need to do is pick the Remove button. Then power cycle the IceBox and then go to the web site and go to
My Account > My Recorders and then pick the Settings button for your IceBox device and MAKE SURE the Repeat flag is unchecked and you have saved the changes.
If you have the timers on another device on IceTV, pick the tab Copy timers to a new Recorder and follow the prompts to get the timers to your IceBox.
You then may have to go to the Manage Recorders tab and pick the Settings button and again making sure the the Repeat flag is unchecked and saved, then pick the Resend all recordings for this device button.
Now, if all is well, you should see the timers appear on the IceBox Timers screen. Again, to make sure things work, you may have to do another reboot.
Finally, you can check things are working as they should when you go to My Account > Guide Settings and see the date and time for the IceBox item of Last EPG fetches should be changing based on how frequently you are requesting updates.
I hope you can make sense of this. You know you have an issue of the last time you did an EPG fetch was hours ago or even days ago.
I have an IceBox unit.
If you want to try it, be prepared!
I use a different tag, [R], rhather than [Rpt], not sure why it should make any difference.
Ian
Quote from: IanL-S on January 26, 2023, 04:12:10 PMI use a different tag, [R], rhather than [Rpt], not sure why it should make any difference.
Ian
I used [Rpt] as that is what I had for my T2. Also, if a feature was to allow for the rating of a shoe\w or movie, R might have a different meaning :D