Change IceBox from Dynamic IP to Static IP address

Started by Ian_AW, February 11, 2023, 05:19:31 PM

Previous topic - Next topic

Ian_AW

How straightforward is it to change my IceBox from a Dynamic IP Address to a Static IP Address?

During the setup I wanted to get it going and so did not try and change defaults too much.

Thanks.

prl

If your router supports it, I've always found it easier to tell the router to bind the device's physical address (MAC address) to a fixed IP address on the router, rather than mess around with static IP addresses on the device.

It also means that all the setup for this is in one place (the router).

How to do it, and whether it's possible to do it, varies with router model.
Peter
Beyonwiz T4 in-use
Beyonwiz T2, T3, T4, U4 & V2 for testing

IanL-S

I take the same approach as Peter. Once you reboot the IceBox it will take the assigned IP address.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Ian_AW

I have a DrayTek 8230 router and have it act as a DHCP server from 192.168.1.20 and higher, and the IceBox is connected via Ethernet.

I have all my network devices (laptop, desktop, etc,) have fixed IP addresses as some software requires an IP address to be provided. Every time the IceBox is restarted the IP address changes from 192.168.1.20 to 192.168.1.22. So if I need to access the IceBox recordings I have out there, I have to first search for the IP Address then enter that do access them. With the fun I had with the major update, I had to copy the recordings I had to a hard drive, then copy them back on the IceBox after the update was applied. As I watch the recordings, I can only delete them via Windows Explorer because the propertied does not offer me an option to delete the recording. To do this I have the IP Address. If I have had to reboot the IceBox for any reason, I have to make sure I have the correct one.

It is much the same for my T2 where the best way to resolve this was to assign the T2 a static IP Address. This way there is no change and I can set backups and the like and know backups will not fail. I was hoping toto that with the IceBox.

raymondjpg

Quote from: Ian_AW on February 11, 2023, 07:40:11 PMIt is much the same for my T2 where the best way to resolve this was to assign the T2 a static IP Address. This way there is no change and I can set backups and the like and know backups will not fail. I was hoping toto that with the IceBox.
In LibreELEC a static IP address can be assigned by going to the LibreELEC tab under settings and then Connections. Clicking on the current connection will give you an option to edit, and you can then choose to go to manual and set IP address under IPv4 and/or IPv6 and DNS Servers if you wish.

Just exactly where you will find the LibreELEC tab depends on which Kodi skin you are using.
Beyonwiz T2, Beyonwiz U4, IceBox BYO with Hauppauge WinTV-dualHD (x2), Hauppauge WinTV-quadHD

prl

Quote from: Ian_AW on February 11, 2023, 07:40:11 PMI have a DrayTek 8230 router

Do you mean DrayTek 2830? Googling for "DrayTek 8230" doesn't give me any pages of the DrayTek 8230, but lots for the DrayTek 2830.

The 2830 seems to be a discontinued model, but I had a look at the manual for its successor, the 2832, and it doesn't have the facility to have fixed IP addresses for devices under DHCP. It looks like it's possible to set up something like that, but it's probably not a great way to do it.

So, if you in fact have a DrayTek 2830, it does look like the only way to set up fixed IP addresses to devices is to give the IP addresses outside the DHCP range, and set the IP addresses manually on the devices.
Peter
Beyonwiz T4 in-use
Beyonwiz T2, T3, T4, U4 & V2 for testing

Ian_AW

Managed to work it out.

I used the terms Static and Dynamic however LibreELEC uses Manual and Automatic.

Worked through the LE menus to Network and saw the then current IP Address for the IceBox. Picked it and then Edit and changed it from Automatic to Manual. I gave it 192.168.1.19.

My router is set for a Static pool from 192.168.1.2 to 192.168.1.19, and a Dynamic pool from 192.168.1.20 and above.

192.168.1.1 is the Gateway and my Beyonwiz T2 is 192.168.1.17, and the P1 before that and the Topfield before that. I aam trying to get my P1 and T2 repaired when I get some time to organise it.

I have since rebooted and it is set at the assigned address.

Teddles

#7
nvm