Main Menu

The latest update

Started by Ian_AW, February 06, 2023, 05:53:41 PM

Previous topic - Next topic

Ian_AW

Well, that is not too good.

I downloaded the file in the email, but now the IP address of the IceBox cannot be seen on my laptop. Checked and double checked but not seen on the network. I checked the IceTV web site, and I am getting regular EPG updates, just it cannot be seen on the network.

I have powered down the IceBox and powered back up but no luck. The next thing to do is power cycle my laptop but I have a virtual meeting in a few minutes literally so am going to have to wait an hour or so to do that.

Ian_AW

Ok, finished the virtual meeting, had something to eat and restarted the computer. Still had no luck.

Looked at the email and noticed a couple of \\ in front of the IP Address and the IceBox appeared! Something to store. It's just not something I thought needed to be added.

One thing I did notice that without the reboot there was poor sync between video and audio. This happens when the resolution shifts to 3840 and 30 Hz. Now, I have not changed that as I had 1920 and 50 Hz.

That makes me wonder if the update has been done. I have a few things downloading I have the update file in the update folder.

The next bit is something that has me on edge because it says "...then it will reboot again and load into a clean IceBox installation."

How clean?

Will it preserve existing recordings, or should I somehow backup the recordings in the Recordings folder?

vader1111

The new firmware introduces the ability to do a Soft Reset.  The soft reset retains recordings & timers, but scrubs pretty much everything else.

After a Soft Reset, users will need to go through the LibreELEC and IceTV wizards again.  This resets all Kodi customisations.

Ian_AW

#3
Well, I did a recordings backup anyway and then went through the procedure. All was fine until I did the Soft Reset. It went through asking me for the language, the box name, the LAN connection and then I end up with the Welcome to IceBox screen only there is nothing in it and the system responds to NOTHING on the remote control, including the power button on the remote control.

I am faced with just a single option and that is to power down and then power back up again.

Should I risk it?

I figured that no matter what, power would be disconnected so decided to press the button on the IceBox itself, but that does not respond, so it looks like it has to be unplug the power pack and plug it back in.

Ian_AW

All in all, a disaster.

Very fortunate to have done a backup of my recordings because I have ended up with an empty Recordings folder.

Then the EPG settings has lost my channel groupings and I have to figure out how to either get it back or create it again.

I tried sending the EPG and Timer information back but no luck. I tried a reboot, but it started trying to match channels and is stuck at something like 5% for the last 30 minutes.

Now another reboot looks in order.

Ian_AW

Now, every time I restart the IceBox, it starts a channel scan, finds no new channels and then tries to match channels to these new 0 channels and gets stuck in an endless loop with the progress barely poking past the start. Selecting Cancel then gets in another endless loop.

Now I have to try and find a way of doing a hard reset.

vader1111

It sounds like you did a soft reboot using the old version, which then installed the new version.  Bad move.

What you should have done was copy the update file to the update folder, reboot (this installs the new firmware), then do the soft reset... but there's really no reason for you to be doing the soft reset anyway.

vader1111

Quote from: raj1954 on February 07, 2023, 01:11:49 PMNow, every time I restart the IceBox, it starts a channel scan, finds no new channels and then tries to match channels to these new 0 channels and gets stuck in an endless loop with the progress barely poking past the start. Selecting Cancel then gets in another endless loop.

Now I have to try and find a way of doing a hard reset.
Hard Reset is just above the Soft Reset, in the Settings -> LibreELEC -> System section.

vader1111

The problems you are describing sound typical of the previous firmware versions - not the latest update.  It sounds like you haven't done the update correctly.

Ian_AW

I followed the installation steps as set out.

The first attempt went to the Welcome to IceBox but with a blank window and everything locked up. It required the plug pack to be unplugged and re-plugged as even the button on the IceBox was locked out.

I checked the version number and was correct.

When the unit booted up, it went past this point however the timers were nowhere to be seen, and neither were the recordings. I tried to reboot only to get to exactly the same point.

Multiple reboots later ended up in the same place. The other option was a hard reset. The recordings would be lost (if they were not already lost) but I had backed them up earlier.

Now it started the endless loop where it said IceTV needed some more configuring. It would scan for new channels but find none and then carry on trying to match no channels to the IceTV channel list. Thid would lock things up as long as you let it try. The only way out was a power cycle. On startup it would try and scan for new channels, find none and then try and match them. If you cancelled the scan, you got told that the channels would not be matched. Ok that and then 30 seconds later would start scanning. Cancel it, ok the next screen and it would keep this loop going.

So, I tried one last soft reset in the hope that it would clear the channels. Even here it was touchy and took a few attempts because there was a 30 second wait after a reset request and this meant that the endless cycle would get to a point where it could lock up.

Eventually the timing was just right and there was enough time for the 30 second wait and the timing of the loop and the soft reset kicked in and managed to retrieve the timers. The recordings on the IceBox were lost however I can get them off the backup I made.

If it had not had the first lockup things might have been a little different. Everything was followed as set out. All up it took around 6 hours to complete, and I have to be a little careful with the recordings as some will have the same folder names so need to add a 1 or something to stop them overwriting the others.

vader1111

#10
This definitely sounds like the problems we had with the old firmware - but the new firmware has sorted all of this stuff out.

You should be running version devel-20230205230517-9a5f365.  To confirm this, go to Settings -> LibreELEC -> About.

To escape the loop you were in, you need to cancel while it is scanning for channels - if you wait until it starts matching, it's too late and you'll need to pull the power plug and start again.  If you cancel during scanning for channels, you buy yourself 30 seconds to start the Soft or Hard reset, before it starts scanning for channels again (and you need to cancel again).

IanL-S

I too had this issue with the old firmware. I also seem to be alone in the beta testers who had it happen with the release version (in pre release testing). The prior beta worked perfectly for me, not sure why I had the same problem as reported here. Currently running the prior beta.
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Ian_AW

Quote from: IanL-S on February 08, 2023, 07:32:20 AMI too had this issue with the old firmware. I also seem to be alone in the beta testers who had it happen with the release version (in pre release testing). The prior beta worked perfectly for me, not sure why I had the same problem as reported here. Currently running the prior beta.
This is the link in the e-mail received:

https://updates.icetv.com.au/downloads/IceBox-Generic.x86_64-10.0-devel-20230205230517-9a5f365.img.gz

and just checking the information, I am currently running on the IceBox it is

devel-20230205230517-9a5f365

When I installed it, I checked it on the TV. During startup, this appears in the upper left corner of the screen in very small text. I only went further when the numbers matched.