Main Menu

Cannot Access Ice TV

Started by AJFC, September 02, 2023, 03:57:22 PM

Previous topic - Next topic

TimC

Quote from: AJFC on September 03, 2023, 02:50:51 PMHere is a screenshot of the BOOT tab.  TV scrren Shot BOOT.JPG

I now have exactly the same problem.

I have unplugged the box from power for about 12hrs and again for 16hrs with the same result each time.
I have also tried "Save changes and exit", and "Save changes and reset" with the same ultimate result.

Is there anything else I can try while I wait for the new SSD?
Icebox, Fetch box (Not IceTV Capable)

IanL-S

You seem to have done all of the things that are capable of solving the problem. I would not give up on the unplugging for an extended time - eventually it may work.

Short of a temporary replacement SSD I cannot think of anything else - the good news is that it is relatively easy to swap the SSD (at lest that is the case with my pre-release beta testing setup which has a slightly different case).

If there are any important recordings, there are ways to recover them but can be a bit of a chore.

Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

AJFC

I have returned my Ice Box and hope to receive it back with a new SSD as soon as they are available.
AJFC

Daniel Hall at IceTV

Quote from: TimC on September 19, 2023, 09:44:17 AM
Quote from: AJFC on September 03, 2023, 02:50:51 PMHere is a screenshot of the BOOT tab.  TV scrren Shot BOOT.JPG

I now have exactly the same problem.

I have unplugged the box from power for about 12hrs and again for 16hrs with the same result each time.
I have also tried "Save changes and exit", and "Save changes and reset" with the same ultimate result.

Is there anything else I can try while I wait for the new SSD?

There is one more thing that we have seen work and that is to boot into the IceBox installer, but not actually install it, just let it read the drives, then on the main installation screen just select reboot.

Best way to do this is to follow the instructions for the BYOB setup (and use that download as it's the same file) to create an IceBox installer USB stick. This is found at https://support.icetv.com.au/hc/en-us/articles/6591367595407-IceBox-BYOB-Installation-Links
Regards,

Daniel.
CTO.

TimC

Quote from: Daniel Hall at IceTV on September 19, 2023, 11:16:53 AMThere is one more thing that we have seen work and that is to boot into the IceBox installer, but not actually install it, just let it read the drives, then on the main installation screen just select reboot.

Best way to do this is to follow the instructions for the BYOB setup (and use that download as it's the same file) to create an IceBox installer USB stick. This is found at https://support.icetv.com.au/hc/en-us/articles/6591367595407-IceBox-BYOB-Installation-Links

I'm having a little trouble with this.  There are a few too many choices to make.

Ok I am using a windows PC to download the data, but the Boot USB will be plugged into the Icebox, which is Linux?

So which tool do I use for the creation of the USB Boot disk, "Windows PC" or "Linux/Mac".

Is there a particular format required on the USB:
FAT?
NTFS?
FAT32?
exFAT?

Note: When I run the Windows PC version, the tool gets a write error 3 seconds from the end.

At the "LibreELEC Generic" it provides a bunch of different versions, but I think I am just supposed to download the IceTV version at:
https://updates.icetv.com.au/downloads/IceBox-Generic.x86_64-11.0-devel-20230522060525-aae861d.img.gz.

Note:  The link to:
"https://www.balena.io/etcher#download-etcher" doesn't work.

PS:  Before I had a chance to try any of this, the Icebox started working again.

However, it would be good for next time if someone could provide a simple set of steps to set up the Boot USB.
Icebox, Fetch box (Not IceTV Capable)

MD

Firstly I checked the link and it does work. Not sure why not for you?

Secondly, in areas of unknown tech things often Google (or another good search engine) is your friend.  I typed in "what format should I use on my usb" and got this:  https://www.howtogeek.com/73178/what-file-system-should-i-use-for-my-usb-drive/

Use Fat32 as shown by the conformance chart.


Daniel Hall at IceTV

The link to the Balena Etcher download has been fixed, that was a weird one.

As for the LibreELEC download page, that was just for the "LibreELEC USB-SD Creator" if you have a windows PC, however Balena Etcher is quite easy to use to be honest, so we will likely remove that from the page to avoid confusion.
Regards,

Daniel.
CTO.