IceTV Forum

IceTV IceBox => Getting Help => Topic started by: AJFC on September 02, 2023, 03:57:22 PM

Title: Cannot Access Ice TV
Post by: AJFC on September 02, 2023, 03:57:22 PM
While watching a recorded program on Ice TV the screen went grey, although the program continued.  The control unit did not function so I could not change program or go back or stop.  I then removed the power source, waited and then reconnected.  The Ice TV logo came on OK but the next screen (attached) I had not seen before and am not skilled to understand what I am supposed to do.  Can someone help please.
TonyTV screen shot.JPG
Title: Re: Cannot Access Ice TV
Post by: IanL-S on September 02, 2023, 05:17:13 PM
The screenshot is rather blurred. It looks like on reboot the IceBox has gone into UEFI/BIOS. As I understand it, this is a symptom of the SSD going into read-only mode (IceTV will shortly be replacing the SSD on all of the IceBox units they have sold).

I have never had it happen like this, but my understanding is that the first thing to do is to turn the Ice Box off and unplug it. Leave it unplugged over night and try again in the morning. Hopefully it will then startup as it should.

Ian

Title: Re: Cannot Access Ice TV
Post by: AJFC on September 02, 2023, 05:36:25 PM
Thanks IanL-S, already tried that but will do so again this evening.  How shortly will Ice TV be replacing the SSD as I am now without any access to recordings etc.  It is only about six month old.  How do I contact Ice TV?
Title: Re: Cannot Access Ice TV
Post by: Ian_AW on September 02, 2023, 05:55:08 PM
G'day,

A while back I had a similar thing happen. It is something like the BIOS settings screen, only you cannot retire the screen. I left on overnight and no change so ended up powering off at the wall and then powering back up. It loaded PK, and I have not had it happen again.

I will say that I am lucky to get mine to work for more than 24 hours and when I restart it I get the write errors needing a further restart.
Title: Re: Cannot Access Ice TV
Post by: AJFC on September 03, 2023, 12:31:22 PM
I have left Ice Box disconnected from power overnight - no change! I am attaching a larger screen shot in the hope that might help.   Has anyone any ideas please?TV screen shot.JPG
Title: Re: Cannot Access Ice TV
Post by: IanL-S on September 03, 2023, 12:38:44 PM
Thanks for the new image. What do you see when you move to the Boot Tab? - it should indicate the device that the IceBox is booting from. What device is shown.

My IceBox has an earlier firmware than yours (it is a pre-release beta-testing unit which is physically different which complicates matters).
Title: Re: Cannot Access Ice TV
Post by: AJFC on September 03, 2023, 02:50:51 PM
Here is a screenshot of the BOOT tab.  TV scrren Shot BOOT.JPG
Title: Re: Cannot Access Ice TV
Post by: IanL-S on September 03, 2023, 04:27:39 PM
The boot order is as one would expect. Unfortunately I cannot offer any further assistance.

It is probably best if you create a support request, as MD and the team are best placed to assist you.

If it happened to me, I would just replace the SSD; I have few spare ones on the shelf, or a 1 TB AV 2.5" HDD. But for the vast majority of people this is not an option.

Ian
Title: Re: Cannot Access Ice TV
Post by: MD on September 03, 2023, 05:10:42 PM
The only question we have regarding using an HDD is heat as the box is designed for the much cooler SSD
Title: Re: Cannot Access Ice TV
Post by: AJFC on September 03, 2023, 05:22:45 PM
I have submitted a support request so will await a response.
Thank you for your assistance.
Tonny
Title: Re: Cannot Access Ice TV
Post by: MD on September 03, 2023, 05:26:28 PM
I have replied, with a PM via this forum and via the support ticket, both about two hours ago?
Title: Re: Cannot Access Ice TV
Post by: AJFC on September 03, 2023, 07:33:01 PM
I have received the emails but they only refer me back to the comments in this forum.  I do not understand SSD OR HDD - all I know is that my Ice Box no longer works and no-one is giving me an answer on how to make it work or to replace the defective product.
Tony
Title: Re: Cannot Access Ice TV
Post by: MD on September 03, 2023, 10:31:10 PM
The problem you have, shared with most users of the new IceBox, is that its hard drive is faulty. It is knows as a Solid State Drive, hence "SSD".

Unfortunately it took IceTV some time via many test procedures to determine that the SSD was the cause of the failure that you see. 

Consequently IceTV will replace everyone's SSD with new ones, chosen in light of this experience to be properly suited to the unusual usage patterns unique to TV recording compared to an SSD in a standard PC.

I explained in my reply to you the choices customers have as to how they may have the drive replaced in one of three ways best suited to their preference. IceTV is painfully aware that their experience to date has been a poor one but we are doing our best to move forward with a proper solution.
Title: Re: Cannot Access Ice TV
Post by: IanL-S on September 04, 2023, 10:21:21 AM
Quote from: MD on September 03, 2023, 05:10:42 PMThe only question we have regarding using an HDD is heat as the box is designed for the much cooler SSD

With mechanical drive there is more heat so I place a 120mm USB fan on the top which keeps thing nice and cool. I use them on my Beyonwiz and Toppys. If it is temporary measure, you could leave to top off to aid ventilation.
Title: Re: Cannot Access Ice TV
Post by: AJFC on September 04, 2023, 11:48:08 AM
Thank you Ian for your help, I have requested a replacement or refund.
Title: Re: Cannot Access Ice TV
Post by: TimC on September 19, 2023, 09:44:17 AM
Quote from: AJFC on September 03, 2023, 02:50:51 PMHere is a screenshot of the BOOT tab.  TV scrren Shot BOOT.JPG

I now have exactly the same problem.

I have unplugged the box from power for about 12hrs and again for 16hrs with the same result each time.
I have also tried "Save changes and exit", and "Save changes and reset" with the same ultimate result.

Is there anything else I can try while I wait for the new SSD?
Title: Re: Cannot Access Ice TV
Post by: IanL-S on September 19, 2023, 10:30:28 AM
You seem to have done all of the things that are capable of solving the problem. I would not give up on the unplugging for an extended time - eventually it may work.

Short of a temporary replacement SSD I cannot think of anything else - the good news is that it is relatively easy to swap the SSD (at lest that is the case with my pre-release beta testing setup which has a slightly different case).

If there are any important recordings, there are ways to recover them but can be a bit of a chore.

Ian
Title: Re: Cannot Access Ice TV
Post by: AJFC on September 19, 2023, 11:10:57 AM
I have returned my Ice Box and hope to receive it back with a new SSD as soon as they are available.
AJFC
Title: Re: Cannot Access Ice TV
Post by: Daniel Hall at IceTV on September 19, 2023, 11:16:53 AM
Quote from: TimC on September 19, 2023, 09:44:17 AM
Quote from: AJFC on September 03, 2023, 02:50:51 PMHere is a screenshot of the BOOT tab.  TV scrren Shot BOOT.JPG

I now have exactly the same problem.

I have unplugged the box from power for about 12hrs and again for 16hrs with the same result each time.
I have also tried "Save changes and exit", and "Save changes and reset" with the same ultimate result.

Is there anything else I can try while I wait for the new SSD?

There is one more thing that we have seen work and that is to boot into the IceBox installer, but not actually install it, just let it read the drives, then on the main installation screen just select reboot.

Best way to do this is to follow the instructions for the BYOB setup (and use that download as it's the same file) to create an IceBox installer USB stick. This is found at https://support.icetv.com.au/hc/en-us/articles/6591367595407-IceBox-BYOB-Installation-Links
Title: Re: Cannot Access Ice TV
Post by: TimC on September 19, 2023, 04:46:24 PM
Quote from: Daniel Hall at IceTV on September 19, 2023, 11:16:53 AMThere is one more thing that we have seen work and that is to boot into the IceBox installer, but not actually install it, just let it read the drives, then on the main installation screen just select reboot.

Best way to do this is to follow the instructions for the BYOB setup (and use that download as it's the same file) to create an IceBox installer USB stick. This is found at https://support.icetv.com.au/hc/en-us/articles/6591367595407-IceBox-BYOB-Installation-Links

I'm having a little trouble with this.  There are a few too many choices to make.

Ok I am using a windows PC to download the data, but the Boot USB will be plugged into the Icebox, which is Linux?

So which tool do I use for the creation of the USB Boot disk, "Windows PC" or "Linux/Mac".

Is there a particular format required on the USB:
FAT?
NTFS?
FAT32?
exFAT?

Note: When I run the Windows PC version, the tool gets a write error 3 seconds from the end.

At the "LibreELEC Generic" it provides a bunch of different versions, but I think I am just supposed to download the IceTV version at:
https://updates.icetv.com.au/downloads/IceBox-Generic.x86_64-11.0-devel-20230522060525-aae861d.img.gz.

Note:  The link to:
"https://www.balena.io/etcher#download-etcher" doesn't work.

PS:  Before I had a chance to try any of this, the Icebox started working again.

However, it would be good for next time if someone could provide a simple set of steps to set up the Boot USB.
Title: Re: Cannot Access Ice TV
Post by: MD on September 19, 2023, 07:43:49 PM
Firstly I checked the link and it does work. Not sure why not for you?

Secondly, in areas of unknown tech things often Google (or another good search engine) is your friend.  I typed in "what format should I use on my usb" and got this:  https://www.howtogeek.com/73178/what-file-system-should-i-use-for-my-usb-drive/

Use Fat32 as shown by the conformance chart.

Title: Re: Cannot Access Ice TV
Post by: Daniel Hall at IceTV on September 20, 2023, 08:56:45 AM
The link to the Balena Etcher download has been fixed, that was a weird one.

As for the LibreELEC download page, that was just for the "LibreELEC USB-SD Creator" if you have a windows PC, however Balena Etcher is quite easy to use to be honest, so we will likely remove that from the page to avoid confusion.