Hi, I have an issue where I attempted to do a factory reset and the IceTV software reinstalled but no TV channels. I have TV through the antenna but was unable to get the TV setup done. I unplugged the IceBox and I get the message below. Sorry can't attach the image as it's too big, but it's all strange code stuff. I can't escape out of it. Any feedback most welcome
VIETA
LUNyI agIle
cULL mInICI eLan rIegalI clIvo,
LEIL
Main
Security
Boot
Save & Exit
Save Options
Save Changes and Exit
Discard Changes and Exit
Save Changes and Reset
Discard Changes and Reset
Save Changes
Discard changes
Default Options
Restore Defaults
Save as User Defaults
Restore User Defaults
Boot override
Windows Boot Manager
Launch EFI Shell from filesystem devise
Attempts to Launch EFI Shell application (Shell efi) from one of the available filesystem devices
WARNING
Not Found
OK
+*: Select Screen ft: Select Item
Enter: Select
+/-: Change Opt.
F1: General Helo
F2: Previous Values
F3: Optimized Defaults
F4:
Save 3 Exit
ESC: Exit
Panasonic
Hi Stephanie,
Try pulling out its power pin and pressing its on/off button at the same time. Wait five minutes or so then plug it in again. If it restarts properly go to Settings (the cog at the top) - Addons - Services - IceTV and if it has updated it will be v1.41.
Thanks I will give it a try
I didn't have any luck sadly. Still at the strange code page
Ok unplug it again and leave it over night. Sounds very unscientific but it seems to work. We are in discussions with the SSD manufacturer as to why and doing tests ourselves.
Also, if it does start up after tonight run a soft reset via LibreELEC found in settings.
I have had the Icebox off and unplugged all day and night. I still have the 'coding' on my screen and can't get out of it
This is not good news. I have several thoughts on what to try next, but I think it best to wait a response from MD.
Ian
Thank you Ian
Next thing to do would be to try one more time to leave it overnight completely unplugged and to try again tomorrow.
If that fails the next step is to attempt to reload the firmware via a USB stick, the downside of this is that it will lose any recordings that are already on the IceBox.
Hi Daniel, thanks for your message. I can't do that unfortunately, I don't t have a laptop or PC
Quote from: stephanie70 on May 27, 2023, 12:57:20 PMHi Daniel, thanks for your message. I can't do that unfortunately, I don't t have a laptop or PC
Stephanie,
What type of device are you using to post to this forum?
Is this like the message you are getting?
BIOS.JPG
Hi there, I'm on my iPhone 13 sending these messages and yes that's the screen I'm stuck on. When I attempt to save and exit it just bounces back to this screen
Hi Stephanie,
As we can't update it via a PC/Mac try leaving it unplugged again as we've had one other that eventually did restart after a couple of tries. If that fails after tonight, try again tomorrow and the same on Sunday trying again. If they fail I'll post you a USB drive to reboot it with new firmware on Monday.
Remember, if it does restart do a soft reset too.
Thank you
Nevertheless try turning it back on this morning as if it recovers your recordings will be intact and it less hassle than reinstalling the firmware. Don't forget the soft reset. If no go unplug it again and let me know tomorrow morning if it has restarted. If not I'll get a USB stick, load on the firmware, and post it.
Select the "Save change and reset" option and see what happens. Try it multiple times. I managed to get back to normal twice now by trying that option a few times.
Hi Hati I have tried that several times and no luck
Quote from: stephanie70 on June 05, 2023, 09:03:40 AMHi Hati I have tried that several times and no luck
Bummer...