IceTV Forum

IceTV General => General Discussions => Topic started by: mudjeep on July 23, 2006, 03:58:25 PM

Title: Icebox2 Setup Problems
Post by: mudjeep on July 23, 2006, 03:58:25 PM
Hello all.

I am having a devil of a time trying to get my icebox2 to connect to my network. I followed the instructions that came with it, but once i switch it to Automatic -DHCP and try to connect to my wireless network I get nothing.  My router does not seem to see it, despite that I have turned off all security.  I haven't tried the static IP address yet because I'm not sure what to put in the bottom two fields.

Any ideas?  I have a Belkin wireless router.

Jason.
Title: Re: Icebox2 Setup Problems
Post by: brianh on July 25, 2006, 02:09:16 PM
Hi Jason,

You need to know what the IP range of your network is set up as; this can vary with each person, but whoever set up uyour network would be able to find this out.

I would reccomend using a static address, so you can find it to log in to - eg.

I have an ADSL modem (non-wirelss) with IP address range of (say) 192.168.2.1 - 192.168.2.20
The address of the modem/router is,say, 192.168.2.19

I could then set up my Belkin wireless router as an access point with a static IP of 192.168.2.18
I could then set up my IceBox2 with a static IP of 192.168.2.17

The default gateway would  then be 192.268.2.19 (ie. the modem's IP address).

Your modem device (probably your Belkin?) should have DHCP enabled to issue IP addresses to any PC's on your network, but anything like wireless bridges, wirleless routers that can be logged into & configured, should have a static IP so you can locate them reliably.  Keep a list somewhere so you know how it is all put together when you later need to add or modify anything.

Cheers,
Brian H
Title: Re: Icebox2 Setup Problems
Post by: goldcoastguy on July 25, 2006, 06:47:55 PM
The one issue I had in setting up the Icebox 2 was with step 2 of the instruction guide.

QuoteYou will need to specify an IP address for the Ethernet port in your computer that is connected to
the Asus Bridge. If you are not sure how to do this you will need to refer to your operating
system manual. The details that need to be specified are:
a.
IP Address â€" 192.168.1.2
b.
Subnet Mask â€" 255.255.255.0
The rest of the settings can be left blank.

It took me a little while to work this part out.

Here's how it should work on Windows XP.

1. Start Button -> My Network Places (if it isn't there, right click on the Start button, select Properties, click on Customized next to "Start Menu" on the Start Menu tab. Click on the Advanced tab. Tick the box in the "Start Menu Items" list next to "My Network Places")

2. Click on "View Network Connections" on the right hand list

3. Right click on Local Area Connection and select Properties. At this stage, make sure the Local Area Connection is enabled (not disabled).

4. On the General tab, click on Internet Protocol (TCP/IP) and press Properties.

5. Put in the details as per the ICE Install instructions. Hit OK all the way out of there.



Evan :->
Title: Re: Icebox2 Setup Problems
Post by: brianh on July 25, 2006, 08:31:03 PM
Oh, and don't forget to do what Evan said above.... :-[   (of course, I SHOULD have thought of that....)

Once you have done the above, it helps you
1) find the IceBox2 -
2) assign a new static IP address
3) then you can return your PC to get it's IP automatically, as it probably was before - following Evan's instructions above....   

Hope this helps,  ???

Cheers,
Brian H 
Title: Re: Icebox2 Setup Problems
Post by: mudjeep on July 26, 2006, 08:13:16 PM
Thanks for your help guys.  I had managed to do the first step and got initial access to the icebox - my main problem lies in connecting it to my Belkin.

To explain things better, I have an ethernet port in my wall which comes from a wireless broadband antenna/modem on the roof over which I have no interaction.  This plugs straight into my Belkin.  The Belkin address is 192.168.2.1.

Attached directly to that are:
- 192.168.2.2 Netcomm VOIP desktop phone (which doesn't appear on the client list despite being connected)
- 192.168.2.3 Desktop

Connecting wirelessly is:
- 192.168.2.4 Laptop

All addresses are assigned by DHCP

After following the instructions with the Icebox2 I disconnected it from the laptop and connected it to the toppy, but cannot find it connecting to the Belkin, no matter where I look and even when I disable all security.

So now I m ready to try a static IP address as per your advice but haven't done this before.  What do I put in the "default gateway" and "DNS Server" fields on the Icebox2 config page?  Do I need to do anything on my Belkin?

Cheers,

Jason.
Title: Re: Icebox2 Setup Problems
Post by: goldcoastguy on July 26, 2006, 08:36:35 PM
I also have a Belkin, so I'll assume you can access the same pages

At this address http://192.168.2.1/wireless_bridge.html is "Enable Wireless Bridging" ticked? It should be.

At this address http://192.168.2.1/fw_mac.html is "Enable MAC Address Filtering" ticked? It shouldn't be.


Evan :->
Title: Re: Icebox2 Setup Problems
Post by: peteru on July 26, 2006, 09:33:26 PM
If your router has an address of 192.168.2.1, then your default gateway and your DNS server are almost certainly 192.168.2.1 as well.
Title: Re: Icebox2 Setup Problems
Post by: mudjeep on July 26, 2006, 11:34:16 PM
Okay I've done all those things, setting up the icebox at 192.168.2.19 but I'm still having no luck.  Any more ideas, or troubleshooting things to try?

Title: Re: Icebox2 Setup Problems
Post by: brianh on July 27, 2006, 11:54:08 AM
Quote from: peteru on July 26, 2006, 09:33:26 PM
If your router has an address of 192.168.2.1, then your default gateway and your DNS server are almost certainly 192.168.2.1 as well.



Peter,

would the default gateway possibly be the IP address of the Antenna/modem in the roof??  From memory, I tried to set the "default gateway" to my wireless access point & the DNS server to my modem & this wouldn't work - it wasn't until I entered my modem's IP for both settings (following a support call  to Ice) that it worked.... (with my modem being the DHCP device)  I know you are much more knowledgeable about networks than I am ever likely to be, just seeking clarification.. ???

mudjeep,

have you set your Belkin up as your DHCP device? (just so I understand your setup correctly)

Cheers,
Brian H

Title: Re: Icebox2 Setup Problems
Post by: mudjeep on July 27, 2006, 12:17:50 PM
I'm pretty sure the Belkin is the DHCP server.  If I try to put my modem's IP address in those last two fields it says it's not a valid gateway address or DNS host address.
Title: Re: Icebox2 Setup Problems
Post by: mudjeep on July 27, 2006, 04:29:31 PM
Okay folks here's an update.  It looks like the original problem was down to operator error,  :-\ I didn't put my network name in the SSID field.  I thought that it was supposed to stay as Icebox2 for it to show up on my network as that.  So I changed it and whammo.

So with no security everything worked fine.  Upon reintroducing some security to my network I struck problems again. I use WPA-PSK and I set this up on the wireless settings page.  I go back to the info page and it sees my Belkin with the right MAC address and a strong signal.  When I try to set up the IP address, whether auto or static, it doesn't connect properly despite working when there was no security.

I tried many variations of security settings and new paswords but to no avail.

Daniel from the help desk has been helping me but we are stuck at this point.  He suggested that Peter might have an answer to this one.

Jason
Title: Re: Icebox2 Setup Problems
Post by: peteru on July 31, 2006, 08:22:05 PM
It's too hard to tell you what should go where without knowing the full setup of your entire home network.

Best bet would be to provide screenshots of all the various setting pages on you access point, modem, router, DHCP server, IceBox2 and any other device that forms part of your network. Once I can see what's configured and how, I can probably give answers that will make it work.
Title: Re: Icebox2 Setup Problems
Post by: perthwa1 on September 07, 2006, 01:17:19 PM
It is interesting to see that I am not the only one who has/is having problems getting the icebox to join a wireless network.  Does anyone have any experience connecting to an Apple Extreme Base Station?

Where my attemps to set up the Icebox fails is at that terrible step two (network settings) in the set up instructions.  I have tried both manual and DCHP, having the base station with and without security (WEP at first and then WPA).  When I click the save button in the Network Setting page, it just hangs and I can no long connect to the icebox via Cat 5 using its factory default IP address (I then just reset and try again).

This is my set up:
Netgear NB5 ADSL modem connected to an Apple Extreme Base Station via Cat 5 Ethernet cable.  2 X Laptops and 1 desktop (all Macs) join that network and successfully connect to the internet.

I noticed that the Modem has the same IP address as the Icebox (192.168.1.1) -don't know if this is important.  The Apple base station distributes IP addresses to the computers in the 10.0.1.1 range (Base Station is 10.0.1.1 and the 3 computers connected to the wireless network has sequencial address 10.0.1.2 to 10.0.1.4).

I figure that once I set up the icebox's wireless set up page and save that info (always successful) the base station then changes the icebox's ip address.  I have tried to reconnect to the icebox by using the next ip addresses in line but alway get an error message in the browser "fail to connect etc".

Any ideas would be greatly appreciated.

Cheers,
???
Title: Re: Icebox2 Setup Problems
Post by: brianh on September 07, 2006, 10:45:53 PM
Hi,

In the absence of any gurus, I will do my best... :-\   

I don't understand your IP setup; you mention one lot on 10.0.1.n and the modem & icebox on 192.168.1.1 -  Definitely, you will have problems with two IP's the same.. but as far as I can tell, you also have a problem with your network?

Whatever you decide to use, I would keep your whole network on the same range... then if you can connect your Icebox to a laptop/standalone MAC via cable first & set the IP address to somthing unique in that range. You may need to set a static IP on the standalone to get it to talk, then change it back once you have reset the Icebox with the new IP.   Don't worry about security until you have that working.

We really need to know more details of your setup in order to help further, but hope this can get you somewhere.

Cheers,
Brian H
Title: Re: Icebox2 Setup Problems
Post by: perthwa1 on September 08, 2006, 12:12:08 AM
Sorry I didn't make myself clear. Maybe it best to focus on the issue of connecting to my wireless network.  My Apple Extreme Base Station (AEBS) distributes the ip addresses to all the clients using DHCP and within the 10.0.1.1 range.  All those clients access the adsl modem that is attached to the AEBS via the WAN port with a Cat 5 cable.  As far as I understand, what I am trying to do is get the icebox to join that wi-fi network so that it can also access the adsl modem, right?  So, the AEBS should be giving the icebox its new ip address and allowing it to join the network and tunnel through to the modem as it does for all the computers in the house that connect to it.  That what seems not to be happening.  As I said before, following instructions, I set up my laptops' ethernet port to 192.168.1.2 and when I put the factory default IP address of the Icebox into the address line of a browser I see that 'special' icebox page.  Next, I input the WI-FI info as directed and save it.  That seems successful.  At this point I can ping the icebox by using its default IP address (192.168.1.1) via the cat 5 as I can all the computers on the network on the 10.0.1.X range via my wi-fi connection to the base station from my laptop. Now here is where it all falls apart. If selecting auto-DHCP in the network setting page, I get a "can't find the server message".  If selecting manual-static and giving it a 10.0.1.27 ip address (so I know an exact ip address to get back to icebox) and a net mask of 255.255.255.0 and the gateway and server address of the AEBS router (10.0.1.1) ( this is exactly what each wi-fi client on the network has (except for a different ip address of course) I get the same result.  At this point, I try to ping the icebox again but that doesn't work either on the old default address or on the one I gave it (10.0.1.27).
Does this give you enough info?  If not, let me know what settings etc. you need to do a diagnostic.
Thanks for you help in this matter.
Cheers,  ???
Title: Re: Icebox2 Setup Problems
Post by: perthwa1 on September 08, 2006, 01:54:15 AM
Surely IT is more akin to voodoo than to science.  Lo and behold My Icebox works.  Why, I can't say as I haven't done anything different just now that I hadn't tried before.  I did wait longer before I pinged the Icebox with the static address.  I also took all security off (but I tried that before with no success).   What I did do different was give it a netmask of 255.0.0.0 which, I was told, indicates a class A device (dumber device type) instead of 255.255.255.0 which is a class C device (smarter). I may have reversed that explanation re the device types?
Of course I rather not leave the network with no wi-fi security and will try to put it back on and report back for those who might experience the same problem in the future.
Thanks to all from the forum and the IceTv Help Desk who have been great.
Cheers,
;D
Title: Re: Icebox2 Setup Problems
Post by: perthwa1 on September 08, 2006, 05:42:13 PM
I am happy to report further success in setting up my new IceBox2 to my home wi-fi network.  All is working well and I even have wi-fi security implemented (WPA2). For all those who are still having problems (especially those using apple wi-fi routers-Extreme Base Station, etc), I suggest the following:Firstly, it might help to understand what you're trying to do (especially if you're not an IT expert which I am definitely not).
Typical Scenario:You have a computer or computers connected to the internet via some sort of wireless device (either a wireless modem/router combo or a separate adsl modem attached to a Wi-Fi router/base station/etc that feeds that internet connection to all your computers.
Given that, the task is to allow the IceBox to connect to the existing Wi-Fi network just like one of you computers.  If your computers can do it so can the IceBox!
Once connected, the IceBox will be able to access the internet, pull down the IceTv EPG and you won't have to think about it anymore. At least anymore than you think about what happens in the background when you throw a light switch or turn on the water tap.
Now to the connection process:
Plug the IceBox into your Desktop/Laptop  ethernet port via the supplied Ethernet Cat 5 Cable Set up that port to 'see' the Icebox.  If you have a Mac you do that by going to System Preferences/Network/Show:Built-in Ethernet and click the TCP/IP tab. On the dropdown menu next to "Configure IPv4" select 'Manually' and follow the ice instructions to set up that port to the recommended ip address (192.168.1.2) and subnet mask 255.255.255.0.  Click Apply Now. This is the first step in the standard instructions supplied by IceTV.  If you have an Intel Based PC running some form of windows, there are equivalent system setting control panels or whatever (sorry, can't help you here, I don't do windows!).
Launch a browser (note that I noticed that the apple browser, Safari, and Internet Explorer behave/look a little different when going through these processes but you get to the same place in the end.
Type into the address line of the browser the recommended factory default ip address of the icebox (http;//192.168.1.2) and hit enter.
You should now see the 'special' Icebox2 page with all the selectable functions on the upper lefthand side.
Now leave that alone for a while as you have to find out some info about your wi-fi routers' network settings.
The Apple Extreme Base Station has a management utility (AirPort Admin Utility).  Other brands of Wi-fi routers would have a similar piece of software that would have been loaded on your computer when you setup your wi-fi network. Although I can only explain what I did on my set up, I think that all wi-fi routers will have a similar setup.
For the Apple product Airport Extreme Base Station do the following to find you wi-fi network info:
Launch the AirPort Admin Utility.
You should see the Airport Extreme Base Station highlighted (if not, click on its name to highlight it).
Click on the configure icon at the top of that window.
You will have to type in the password you set up to allow management of that device when you set it up.  Forgot that?  If so, check the manual to see how to do a password reset.
Once into that utility, you will see a page with 6 tabs along the top; Airport,Internet,Network, etc..  The Airport and Network Tabs are the ones where you are going to get the info you need to feed into the Icebox setup.
Click the Airport tab.  Take note of the Airport Network Name.  This is what you are going to type into the SSID field in the IceBox Wireless Settings Page later.
Also note down the 'Wireless Security' method. (I started the icebox setup by turning off all security - there is a "change wireless security" radio button on this page that allows you to choose different types of security or no security - you can change this back later). I also changed the "Channel" from Automatic to Channel 1.
Next click the Network tab. You will notice that the 'Distribute IP Addresses' box is ticked and that the "Share a single IP address (using DHCP and NAT)" is also selected.  If not, select those boxes.
Now take note of what is on the drop down menu under the "Share a single IP address (using DHCP and NAT)" tickbox.  Mine says "Use 10.0.1.1 addressing". This may be the Apple default.  Leave this as is.
Now you can click the update button at the bottom of the page.  Your base station will now reboot reflecting any changes you might have made.  Note you may have to rejoin that wireless network.  If you took all security off, all you have to do is select the airport network name in the Airport Icon at the top of your screen.
To recap, you should now have the name of your Airport network, the addressing range and, if you didn't turn off the wi-fi security, the type of wireless security ande password written down.
Next go to that browser window that you opened before when you connected to the IceBox.  If you closed that window just open a new browser window and type into the address line the recommended factory default ip address of the icebox (http;//192.168.1.1) and hit enter.
After that loads up, select the Wireless Settings Page.
If you removed security from your base station, select no security from the dropdown menu of the Security field. A number of the fields will now disappear.  In the SSID field, which came up as a default saying "IceBox2", type in your "Airport Network Name" that you wrote down.
Click the save button. The screen will change telling you that those setting have be saved (Done) and that the network setting have been applied.  After that process is finished, click on "Network Settings" on the lefthand side of the page.
Select "manual-static" setting not the auto-DHCP from the dropdown menu of the Network Configuration field.
Next, type in a unique IP address that wasn't being used by the networked devices (computers, printers, etc) that are on your wireless network.  On Apples, it is hard to determine what IP addresses are being used without going to all of the devices individually and checking this out in the System Preferences of those devices.  An easy way to deal with this is to make up a number that is way more than the number of devices that you might have connected either by Cat 5 Ethernet cable or Wi-Fi to your base station.  If your base station was using the 10.0.1.1 range, for instance, then the base stations IP address is 10.0.1.1. The computers or printers attached to the network (either via cable or wirelessly) would, say, have the ip numbers of 10.0.1.2, 10.0.1.3, 10.0.1.4, etc..  I chose the IP address for my Icebox to be 10.0.1.25 and I typed this number into the IP Address field on the Icebox Network Setting page.
Now here comes the crunch!  The next field down is the Netmask field.  I gave it a class A device number of 255.0.0.0. Before I tried to use 255.255.255.0 and all my attempts of connecting the icebox failed so I suggest you try the 255.0.0.0 number in this field.
In the next two fields (Default Gateway and DNS Server) type in the IP address of your Wi-Fi Router.  Which for my Apple Base station was 10.0.1.1 and click save.
Now, this is where things had been going haywire before.  What you have done is change the IceBox's IP address so now you can't connect to it by addressing http;//192.168.1.1 anymore  Up until now this is how your browser was interfacing with the IceBox.  If you try and select anything on the browser page that you have, up to now, have been working on, it will just timeout and ultimately give you the message "Can't find the server etc". The IceBox should now have the address 10.0.1.25 (if you used my numbering system).  
Note that this process takes a while (a minute or so) to happen and it seems that everything has crashed.  No fear!  Open a new browser page and type in http://10.0.1.25 and you should see the IceBox page again.  Select the Information Page from the list on the left and you should see all your new settings. You should now be able to follow the rest of the Ice instructions as to connecting to the Toppy or otther PVR and downloading the EPG.  This all worked flawlessly for me but was I happy? No!  I was not comfortable by not having any security on my wireless network.  So, I started the process all again.  First, I went into my base station via the AirPort Admin Utility software.  The only thing I changed was to select WPA2 as my wireless security method (you have to create an eight character password- write this down as you will need it later). Click update and let the Base Station reset (takes a minute or so). When that was done I reset the IceBox by pressing the little button on the back of the unit.  I connected the Icebox to my laptop via the Ethernet cable again and connected to the Icebox via a browser window by typing in the http;//192.168.1.1 address. Then I started at the Wireless Settings page again.  This time I chose WPA/WPA2 in the Security field, WPA-PSK,WPA2-PSK in the WPA Mode field, AES+TKIP in the WPA Crypto Algorithm field and also typed in my 8 character password that I just created in the AirPort Admin Utility's security section into the WPA-PSK Passphrase field.  Save those settings as before. When that is done input the same info into the Network Setting Page as explained above.  Follow the same procedures and you should be OK. When you do reconnect to the IceBox using the http;//10.0.1.25 address, go to the Information page to see all the details you put in.  I suggest that you print this out for your records.  You should also follow the IceTv instructions for downloading and reconnecting and restarting your toppy/PVR.  You should now be able to place the Icebox at the back of your entertainment unit/etc. and let it gather dust, secure in the knowledge that you will never have to hassle this again.
Cheers,
;D
Title: Re: Icebox2 Setup Problems
Post by: chrisll on November 26, 2006, 08:02:05 PM
Thanks to all who contributed to this post- has been most helpful. I had my IceBox2 up & running, connected to a Topfield 5000, but disconnected to upload a new TAP. Since then have been unable to reconnect (similar to original posting) but cannot even get wired connection to the IceBox via ethernet port & instructions on this thread. Support have been helpful but cannot solve problem. I'm beginning to think it must be a problem with the IceBox itself. Any way of determining this ??
Chris
Title: Re: Icebox2 Setup Problems
Post by: johnminna on March 08, 2019, 03:56:28 AM
I had an issue with Icebox2 Setup, after reading some posts I found solutions.
Thanks
Regard
John