Main Menu

Lan file transfer speed

Started by gerhardp, September 17, 2026, 04:55:32 PM

Previous topic - Next topic

gerhardp

I have used an HP Prodesk 600 I3-8100 box and installed ICETV on it.  I have 3 XBOX One tuners, Flirc USB, Sofabaton remote.  All working nicely, except transferring files from my Windows PC is practically comatose - around 8-9mbps transfer speed.  Network is Gigabit.

I have tried numerous settings like cache, special advancedsettings.xml file, etc with no success.  What's confusing me a bit is there are network service settings in Libreelec and also in Kodi - do these have to be synchronised perfectly or does Samba only rely on Libreelec settings?

It's not a huge thing but should be fixable. Lots of confusing things on google searching.

IanL-S

I have not seen trasfer speeds that slow on either of my BYOB. My BYOB are Intel NUC with (presumably) an Intel one. Whatever it is it give srsfer speeds that are in the regioun of 90 Mbps. However my preproduction IceTV Ice Box has been giving similar speeds to those you are seeing.

Have not thought about adjusting the settings in either KODI or Libreelec. I am running a beta installation, but the LibreELEC build is that in the public firmware, only the IceTV add-on (and possibly the TVHeadend add-on) are different. But that should not impact of network performance.

Have you checked the BIOS settings for the NIC? There may be someting there that is causing the slow speed. Just rembebers that I was going to try a different Ethernet cable - the cable could be damaged or not up to specification. Another possibilityis that the KODI/Libreelec NIC driver is suboptimal, particularly if it is an HP rather than the ones usually found in PCs (Intel, Killer etc).
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

raymondjpg

Quote from: gerhardp on September 17, 2026, 04:55:32 PMAll working nicely, except transferring files from my Windows PC is practically comatose - around 8-9mbps transfer speed.  Network is Gigabit.
Is it possible that there is  a problem with you Windows PC's LAN performance, rather than your HP Prodesk?
Beyonwiz T2, Beyonwiz U4, IceBox BYO with Hauppauge WinTV-dualHD (x2), Hauppauge WinTV-quadHD

gerhardp

Quote from: raymondjpg on September 18, 2026, 09:59:32 AM
Quote from: gerhardp on September 17, 2026, 04:55:32 PMAll working nicely, except transferring files from my Windows PC is practically comatose - around 8-9mbps transfer speed.  Network is Gigabit.
Is it possible that there is  a problem with you Windows PC's LAN performance, rather than your HP Prodesk?

No

gerhardp

Quote from: IanL-S on September 17, 2026, 08:52:40 PMI have not seen trasfer speeds that slow on either of my BYOB. My BYOB are Intel NUC with (presumably) an Intel one. Whatever it is it give srsfer speeds that are in the regioun of 90 Mbps. However my preproduction IceTV Ice Box has been giving similar speeds to those you are seeing.

Have not thought about adjusting the settings in either KODI or Libreelec. I am running a beta installation, but the LibreELEC build is that in the public firmware, only the IceTV add-on (and possibly the TVHeadend add-on) are different. But that should not impact of network performance.

Have you checked the BIOS settings for the NIC? There may be someting there that is causing the slow speed. Just rembebers that I was going to try a different Ethernet cable - the cable could be damaged or not up to specification. Another possibilityis that the KODI/Libreelec NIC driver is suboptimal, particularly if it is an HP rather than the ones usually found in PCs (Intel, Killer etc).

I'm using a 2.5Gb NIC in the Prodesk, connected to a 2.5Gb switch, which is connected to the 1Gb main switch.  I will try connecting to the HP NIC as your suggestion that the Libreelec driver isn't up to par sounds playsible.

IanL-S

Thanks for the additional information. I found a post on the LibreELEC forum which gives some backgrpund:
https://forum.libreelec.tv/thread/25007-2-5-gbit-s-ethernet-adapter-for-libreelec/

The problem may be solved if/when the next buid of IceTV is released - it seems Linux kernal 7.1 may be need for better support for 2.5Gbit.

IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

gerhardp

Quote from: IanL-S on September 18, 2026, 11:49:51 AMThanks for the additional information. I found a post on the LibreELEC forum which gives some backgrpund:
https://forum.libreelec.tv/thread/25007-2-5-gbit-s-ethernet-adapter-for-libreelec/

The problem may be solved if/when the next buid of IceTV is released - it seems Linux kernal 7.1 may be need for better support for 2.5Gbit.


Thanks for that.  I just connected via the onboard 1Gb NIC and if anything transfer speed was a bit slower.

So then I plugged in an old usb AC600 wifi adapter (Unifi IW7) and now getting 30Mbps transfer.  Found a USB 8156 in the stash and tried that one -  no good either, 8mbps. 

Have to investigate my in-wall cable, starting to suspect that is chewed......it's pretty old, but should still be good enough for gigabit.

gerhardp

Update - the problem is in my wall cable.  I suspect some rodent chewage.  I plugged the switch to which the Prodesk is connected to the IW7 port (easiest one to access) and am getting 90mbps through a USB dongle.  The onboard HP port is 100mbps.

Thanks for the help.

raymondjpg

Quote from: IanL-S on September 18, 2026, 11:49:51 AMThanks for the additional information. I found a post on the LibreELEC forum which gives some backgrpund:
https://forum.libreelec.tv/thread/25007-2-5-gbit-s-ethernet-adapter-for-libreelec/

The problem may be solved if/when the next buid of IceTV is released - it seems Linux kernal 7.1 may be need for better support for 2.5Gbit.
I looked into that but as far as I could establish the HP Prodesk 600 I3-8100 has an Intel I219-LM GbE 10/100/1000 Mbps (Gigabit Ethernet) connection. I could understand potential for issues if it were a Realtek LAN port (showing my prejudice there) but it looks more like it comes down to a hardware or wiring issue between the HP, switch(es) and Windows PC.
Beyonwiz T2, Beyonwiz U4, IceBox BYO with Hauppauge WinTV-dualHD (x2), Hauppauge WinTV-quadHD

gerhardp

Quote from: raymondjpg on September 18, 2026, 12:56:52 PM
Quote from: IanL-S on September 18, 2026, 11:49:51 AMThanks for the additional information. I found a post on the LibreELEC forum which gives some backgrpund:
https://forum.libreelec.tv/thread/25007-2-5-gbit-s-ethernet-adapter-for-libreelec/

The problem may be solved if/when the next buid of IceTV is released - it seems Linux kernal 7.1 may be need for better support for 2.5Gbit.
I looked into that but as far as I could establish the HP Prodesk 600 I3-8100 has an Intel I219-LM GbE 10/100/1000 Mbps (Gigabit Ethernet) connection. I could understand potential for issues if it were a Realtek LAN port (showing my prejudice there) but it looks more like it comes down to a hardware or wiring issue between the HP, switch(es) and Windows PC.

Thanks, seems you missed my last post where I confirm an in wall cable issue. :)

raymondjpg

Quote from: gerhardp on September 18, 2026, 01:20:01 PMThanks, seems you missed my last post where I confirm an in wall cable issue. :)
I did but thought it best to post to counter any notion that your IceBox BYO issue might have anything to do with LibreELEC LAN drivers. As a matter of interest my guess, based on my knowledge of a Geminilake NUC from about 10 years ago, is that IceTV's IceBox has a Realtek 8111HN Gigabit Ethernet Controller, yet we have seen no instances of issues with this recently on this forum. I might also add that I have seen no issues relating to LAN port speed on my 8th generation NUC IceBox BYO which has an Intel I219LM Gigabit Ethernet Controller.
Beyonwiz T2, Beyonwiz U4, IceBox BYO with Hauppauge WinTV-dualHD (x2), Hauppauge WinTV-quadHD

gerhardp

Further update - I unplugged the wall patch leads and tested the in wall cable - no issues.  Plugged it back together and am now getting 110mbps on the HP Intel NIC.

So I am giving up and making no more changes to any settings!  All is running as it should.

Thanks again for help.