I'm attempting to install BYOB to a spare Lenovo M920Q mini PC with an Intel i7-8700T with 16GB ram and a 1TB SSD and two ICE Tuners. (With the instructions as per the website.)
The installation from USB appears to go smoothly but:.
1. On initial boot of LibreELEC the first message pop-up is "Communication Server Failed To Start"
2.When the install indicates "Installation Almost Complete" and asks for "NEXT", the setup of WiFi is skipped (Wired LAN is OK), ICETV setup is also skipped and The KODI menu appears.
3. Subsequent Popups: Headend Server 4.2 Update Fail and PVR Manager Fails To Start.
I can trawl thru the setup menus and enter WiFi details and ICE details but that doesn't help obviously. A manual update of the Headend Server also fails.
I've looked at the Lenovo BIOS and checked that nothing should be inhibiting a Linux installation, and tried the install abou seven times now - with the same results, so it looks as if the PC might be the issue. It was previously happily running Windows 11.
If anyone has any ideas to try I'd be most pleased, otherwise I might try a PC or laptop of lesser spec and see what happens. My Beyonwiz T4 is currently stuffed, and my old DP-P1 (now back in service) is a bit flaky... so life is not worth living!
Regards, Rob
Edit: I've installed onto an old i5 laptop with exactly the same result except that it did allow wifi detail entry, then skipped ICE and jumped to KODI. Communication server failed again, no headend no pvr manager...
When the setup wizard starts there is always a message about being unable to access TVHeadend, after a few moments a message appears saying successfully connected - not sure why this is not happening in your case. The failure to do network setup suggests something more serious is wrong, as is the failure to complete the setup.
One possibility is that the installation media has become corrupted; try downloading it again and then install it onto the USB drive.
Before doing a reinstallation, you could try a hard reset which will remove anything left over from the aborted IceTV wizard run. After rebooting, the setup wizard should run (hopefully to a successful completion).
Thanks Ian. I was thinking a corrupted install image... But I've downloaded the image twice, installed to separate USB sticks and tried the install on three machines now - two i5 laptops of different vintages and the newer i7 mini box.- with the same result. I think it has to be the install image.
Is there another link to perhaps a newer image or a different repository?
By hard reset do you mean a cold boot or a complete HDD wipe?
Meanwhile I'll download the image to a different location (just for fun) and try again.
Update: This time I was able to enter wifi details but not Ice login. Subsequently I can enter Ice details manually but no fetch occurs.
And: The event log says TVheadend HTSP Client server is unreachable and TVheadend server 4.2 Update Failed.
Thanks for the update. You do a hard and soft resets by going into (Kodi) Settings, then into LibreELEC (right had side of first row), then select system and go down to Reset Defaults, where you can choose soft and hard reset.
Ian
Thanks Ian. Hard Reset done. At startup I can enter WiFi details, LAN is OK & WiFi is OK, but Ice setup is still skipped and TVheadend does not start - and will not update.
Unless there's some screwy Router, LAN or WAN issue at my end, surely the downloaded image must be corrupted? But having said that you'd really expect the install to just fail. All settings appear to function normally otherwise, but I don't have a TV Headend. The default tuner drivers appear to install normally and they are brand new from Ice.
I've been at this all day today (and most of yesterday) but tomorrow I might temporarily bypass my router and connect the box direct to my Optus 4G modem. That will bypass the router's firewall and secure DNS etc.
Quote from: srto2 on July 04, 2023, 06:45:53 PMbut I don't have a TV Headend.
'tvheadend' is actually a process running on your IceBox. Kodi is the front-end GUI that you see on the screen, 'tvheadend' sits behind the scenes doing the actual recordings, etc.
You can try to browse to tvheadend by going to 'http://
[IP Address of your IceBox]:9981'. This will tell you if tvheadend is running.
Another thing to check in Kodi is the setting for the 'Tvheadend HTSP Client' addon. Ensure that the IP address is 127.0.0.1 (This always means 'this machine') and that the HTSP port is 9982.
Quote from: DeltaMikeCharlie on July 04, 2023, 07:07:12 PMYou can try to browse to tvheadend by going to 'http://[IP Address of your IceBox]:9981'. This will tell you if tvheadend is running.
Another thing to check in Kodi is the setting for the 'Tvheadend HTSP Client' addon. Ensure that the IP address is 127.0.0.1 (This always means 'this machine') and that the HTSP port is 9982.
I have created another install USB stick on completely different PC and installed ICE to a virgin SDD. I have connected the WiFi directly to the service that Optus 4G provides (a multi layer private network) thus bypassing my Router. The result is the same. I can install WiFi details but that's it. The install bypasses any other setup and jumps to KODI. Any other install/setup input can be installed from appropriate menus but nothing works.
The machine appears on my network ie (after restoring its connection to my Router) but the headend cannot be reached with a browser. I can browse the contents of the drive with a file manager. But I don't know what settings need to be checked or changed. Presumably SSH will work, too. From the add-ons menu the HTSP settings appear to be correct. The TVHeadend Server 4.2 appears to be installed... The settings are set to defaults.
If I switch to TV on the main menu the PVR server startup remains at 0% forever.
After about 20 installs on three different machines with the same result I have to conclude that there is either something screwy with the install image - or I am making some weird mistake over and over ad-nauseam - or my Optus 4G internet connection is inhibiting some required module.
Now, I know this thing is in Beta but I didn't expect this sort of issue. There must be a newer version of the install image, or at the least, a copy from another repository. Surely.
For the moment I have run out of ideas and I'm hoping for some more input from a guru!
When you have done the wifi setup do you have an IP address in the chosen wifi pane? If so, after that, does it go to SMB/SSH which can be left as the default SMB only, then on pressing "next " the next pane that comes up should say please simply wait for up to 30 seconds until the IceTV setup menu appears. Don't do anything until it does. It is very important to DO NOTHING or the IceTV setup will be skipped. Once it's appeared fill in your IceTV details and then channel scans, EPG matching and timers should run.
Quote from: MD on July 05, 2023, 01:30:07 PMWhen you have done the wifi setup do you have an IP address in the chosen wifi pane? If so, after that, does it go to SMB/SSH which can be left as the default SMB only, then on pressing "next " the next pane that comes up should say please simply wait for up to 30 seconds until the IceTV setup menu appears. Don't do anything until it does. It is very important to DO NOTHING or the IceTV setup will be skipped. Once it's appeared fill in your IceTV details and then channel scans, EPG matching and timers should run.
Thanks Boss! Yep. All of that. Many times now. The IceTV setup menu NEVER appears. I've even gone to make coffee or have lunch waiting for the IceTV setup to appear. So no channel scans, no EPG. It always just jumps to the KODI menu.
The TVHeadend Server 4.2 appears to be installed but I can't reach it with a browser as suggested by DMC. I can browse the drive with a file manager.
As I've detailed I have tried this install many times now on three machines - and I can't tear my hair out because I don't have any... I'm sure there's something screwy happening but I don't know where to start looking beyond what I've already done.
NOTE: At the point where you press "NEXT" and wait for the IceTV setup I get the pop-up "TVHeadend Server 4.2 Update Failed" The IceTV setup never appears.
Are you sure you get a IP address at the network setup section otherwise you can't setup IceTV?
Why do you specifically need to access TVHeadend? If the installation follows through to the completion of the IceTV user details the channels will be scanned etc.
Quote from: MD on July 05, 2023, 02:35:09 PMAre you sure you get a IP address at the network setup section otherwise you can't setup IceTV?
Why do you specifically need to access TVHeadend? If the installation follows through to the completion of the IceTV user details the channels will be scanned etc.
Absolutely I get an IP address. I can ping the box and I can browse the SDD remotely with a filemanager.
I don't want to access the TVHeadend! Believe me! A message pops up that an update to the TVHeadend failed. That's at the time I would expect the IceTV menu to appear but it never does.
It seems to me that is the point of failure. But what would I know!!
Subsequent trawling thru the menus shows that an update to the TVHeadend is available, but it won't install from there either. The installation fails from there too.
If the thing is trying and failing to update itself on the initial installation maybe a patch to the install image might effect a fix?
Please!
Is the IP address visible in the network setup section? If not you are not connecting.
If connected once signed in to IceTV a very brief, maybe 2 seconds max, TVHeadend "not connected" message will appear but as it connects via IP a successful connection message will appear.
I suspect you either don't get an IP address in the initial BYOB setup page, the third one after language and then naming the box, or you have a local network issue that is holding back a proper connection. We have thousands logging in every minute and no issues whatsoever.
Under the settings of Kodi, in the LibreELEC settings, under the About tab on the left, what is the version number that is displayed?
I have an idea on what the issue is now, and if you are using a mini PC then you won't have an nVidia graphics card in play, I have just had the download links updated with the latest version of the IceBox BYOB software, please install that on the machine and give it another go.
The download links can be found at https://support.icetv.com.au/hc/en-us/articles/6591367595407-IceBox-BYOB-Installation-Links (https://support.icetv.com.au/hc/en-us/articles/6591367595407-IceBox-BYOB-Installation-Links)
Quote from: MD on July 05, 2023, 03:03:31 PMIs the IP address visible in the network setup section? If not you are not connecting.
If connected once signed in to IceTV a very brief, maybe 2 seconds max, TVHeadend "not connected" message will appear but as it connects via IP a successful connection message will appear.
I suspect you either don't get an IP address in the initial BYOB setup page, the third one after language and then naming the box, or you have a local network issue that is holding back a proper connection. We have thousands logging in every minute and no issues whatsoever.
Thanks for sticking with me.
Yes, the IP address is visible in the network setup. I have no problem in telling you that it is 192.168.1.134 LAN and/or 192.168.1.89 WiFi.
Yes, the "TVHeadend not connected" message does appear briefly BUT at the point where the IceTV setup is supposed to occur I get another popup that says
"TVHeadend Server 4.2 Update Failed" and I can assure you that I have not initiated anything else at that stage.
I have tried this now on three machines with multiple install sticks and multiple hard drives all up probably 30 times now. I've bypassed my LAN completely by connecting direct to my modem.
It's the same error every time with the same result and it has to be a install software issue, doesn't it?
Quote from: Daniel Hall at IceTV on July 05, 2023, 03:05:23 PMUnder the settings of Kodi, in the LibreELEC settings, under the About tab on the left, what is the version number that is displayed?
devel-20230205230517-9a5f365
Daniel Hall, our CTO & Software Manager replied after my last cone commenting as to whether your setup had an NVIDIA graphics card. That may be the cause and we have a solution
Quote from: Daniel Hall at IceTV on July 05, 2023, 03:15:08 PMI have an idea on what the issue is now, and if you are using a mini PC then you won't have an nVidia graphics card in play, I have just had the download links updated with the latest version of the IceBox BYOB software, please install that on the machine and give it another go.
The download links can be found at https://support.icetv.com.au/hc/en-us/articles/6591367595407-IceBox-BYOB-Installation-Links (https://support.icetv.com.au/hc/en-us/articles/6591367595407-IceBox-BYOB-Installation-Links)
Writing the USB stick now...
Quote from: MD on July 05, 2023, 03:30:20 PMDaniel Hall, our CTO & Software Manager replied after my last cone commenting as to whether your setup had an NVIDIA graphics card. That may be the cause and we have a solution
Repies are thick and fast now. I'm about to install with the new image.
Hi Daniel,
Kodi version is STILL 9a5f365.
Let me try a download again
The video "card" in the box is Intel UHD Graphics 630 if that helps!
That's perfect, just need to ensure that the version after installation is 'devel-20230522060525-aae861d' and you should be all good to go.
Daniel, the new download link still points to the older file...
*aae861d.img returns file not found
Hello! Is anyone there? Sorry to be impatient but your new link still points to the older image...
The link text and the link URL did not match. I copied the link text and pasted it into my browser and I got the right file.
Try this: https://updates.icetv.com.au/downloads/IceBox-Generic.x86_64-11.0-devel-20230522060525-aae861d.img.gz (https://updates.icetv.com.au/downloads/IceBox-Generic.x86_64-11.0-devel-20230522060525-aae861d.img.gz)
Hi DMC, thanks for that! I did the same and still got the old file. I'll write the image now!
I do believe the new image is working. Ice is setting up now! Many thanks MD, Daniel and DMC...
Quote from: DeltaMikeCharlie on July 05, 2023, 04:27:30 PMThe link text and the link URL did not match. I copied the link text and pasted it into my browser and I got the right file.
Try this: https://updates.icetv.com.au/downloads/IceBox-Generic.x86_64-11.0-devel-20230522060525-aae861d.img.gz (https://updates.icetv.com.au/downloads/IceBox-Generic.x86_64-11.0-devel-20230522060525-aae861d.img.gz)
Ugh, fixed
Last night I needed to reboot my IceTV IceBox and noticed that at the end of the process there was a message about not being able to contact a remote server. Rebooted several times and got the same message. On the guide settings page it is reported that the IceBox is still calling home. My Week listing indicates all timers have been successfully set for the forthcoming week.
There were 4 failed recordings on Saturday (due to insufficient disk space) but nothing that would explain why I am getting the message on boot-up.
Quote from: IanL-S on July 06, 2023, 08:28:03 AMLast night I needed to reboot my IceTV IceBox and noticed that at the end of the process there was a message about not being able to contact a remote server. Rebooted several times and got the same message. On the guide settings page it is reported that the IceBox is still calling home. My Week listing indicates all timers have been successfully set for the forthcoming week.
There were 4 failed recordings on Saturday (due to insufficient disk space) but nothing that would explain why I am getting the message on boot-up.
Did you mean to start a new topic for this post?
Quote from: srto2 on July 06, 2023, 01:23:46 PMDid you mean to start a new topic for this post?
No, was just that earlier in this thread the notice about failure to connect to external server ... appeared.
In the context, I suspect this message is referring to the IceTV server since the messages about TVHeadend not being connected and then connected refer specifically to TVHeadend. On reflection, I suspect that there is only a delay in connecting to IceTV server (logging into IceTV account). It may have something to do with the IceBox connecting via WiFi rather than Ethernet which could cause a delay in successful log in. I am relatively certain that I do not see it with my BYOB which connect via Ethernet.
I will suggest to the development team that when this happens a 'successful connection' message is displayed. Done!
Update: Daniel Hall says that the remote server message is probably referring to TVHeadend. Unfortunately there is no easy way to disable the message.
My IceBox is no-longer flashing anything on the screen when rebooting.
Hi Ian, I've been a bit snowed under, so no reply 'til now. My machine is not showing the TvHeadend error (now) when rebooting either.
I don't have any issues with getting around Kodi - but I do miss my currently deceased Beyonwiz T4 (let alone any or all of my Toppys, long gone) but I have other issues with either LibreElec (or the IceTV plugin) and my Lenovo mini PC. I'll collate the most significant of those and start another topic when I'm confident it's not "finger trouble" on my part.
Meanwhile the other crazy thing is that SSH worked until I (probably unneccessarily, given my locked down network) changed the default pasword. Something else to think about...