It is recording for me, but it has no channel name, nor metadata
I think I followed all the instructions correctly, attempted to re-fetch several times, makes no difference
Judy, I am seeing the same thing. Not sure what is going on. It could also apply to 10HD but I have not recorded anything on 10HD on the T2.
Ian
It doesn't have "no channel name". It has the wrong channel name, presumably the one used by 7flix in the days leading up to the launch. The channel name isn't in the IceTV data used to set the timer, so it's not IceTV's fault.
Do you see "7flix" named correctly in the Terrestrial TV LCN or the Last Scanned bouquet? If so, I suggest re-doing the rescan that you did when you first rescanned for 7flix before the launch.
Because the channel name isn't stored in the timer, either, that should resolve the channel name if have the cause correct.
Not sure if I was looking at the correct place, but both 10HD and 7flix are listed we I use Open Webif to 'inspect' the T2. I selected LCN tab and then All Channels. And they are both listed there. (Not looking at the unit via TV as the HDMI switch to which it attached has lost the plot. Keep on cycling between active connections.) Should have know better than to buy one from China.
Ian
Quote from: prl on March 03, 2016, 05:12:12 PM
It doesn't have "no channel name". It has the wrong channel name, presumably the one used by 7flix in the days leading up to the launch. The channel name isn't in the IceTV data used to set the timer, so it's not IceTV's fault.
Do you see "7flix" named correctly in the Terrestrial TV LCN or the Last Scanned bouquet? If so, I suggest re-doing the rescan that you did when you first rescanned for 7flix before the launch.
Because the channel name isn't stored in the timer, either, that should resolve the channel name if have the cause correct.
I will re-read your post again manana, as I am half asleep, but not sure I understand. As it happens, I re-scanned it yesterday (before I posted here), because my first thought was that I hadn't done it correctly. The terrestrial TV does show it, as does last scanned (see attached)
You could try deleting the episode on IceTV and wait for the timers to be updated (or force the update in MENU>Plugin>IceTV>Fetch EPG and update timers now).
If that doesn't delete the timer on the PVR, delete it manually.
Then schedule a one-off recording for that episode on IceTV, and see whether the new timer comes through with the right channel name.
This problem may be related to the fact that the scanned serviceref changed for TEN HD when it launched from the one that scanned before the launch date. The change shouldn't affect being able to set IceTV timers, but it might affect the lookup of the channel name.
Quote from: prl on March 04, 2016, 12:05:50 PM
You could try deleting the episode on IceTV and wait for the timers to be updated (or force the update in MENU>Plugin>IceTV>Fetch EPG and update timers now).
If that doesn't delete the timer on the PVR, delete it manually.
Then schedule a one-off recording for that episode on IceTV, and see whether the new timer comes through with the right channel name.
This problem may be related to the fact that the scanned serviceref changed for TEN HD when it launched from the one that scanned before the launch date. The change shouldn't affect being able to set IceTV timers, but it might affect the lookup of the channel name.
Well, I did all of the above, deleted the timer, waited for it to disappear from the Wiz, then re-scheduled it. Came back as "new channel" as before
Not sure if this has anything to do with it, but noticed that these two new channels have no icons. Don't see how that would cause this, just thought I'd mention it.
Incidentally, I have two more questions. Is there a way of changing the size of the EPG on the TV? (see attached photo of the actual TV set, as opposed to looking at it on the Web)
Also, I seem to have acquired a bouquet called Melbourne. Has it got a purpose, before I get rid of it?
csutak40, you're not seeing things. I had "New Channel" happen on my T3 for a scheduled recording of The Amazing Race on 7flix last week. I was too chicken to let it stay that way - I record that show for another family member - so I manually edited the timer to use the 7flix channel, destroying any chance of doing forensics on the cause of the anomaly. It recorded OK.
If it happens again for this week's episode of The Amazing Race I'll post back.
Quote from: futzle on March 05, 2016, 10:38:00 AM
csutak40, you're not seeing things. I had "New Channel" happen on my T3 for a scheduled recording of The Amazing Race on 7flix last week. I was too chicken to let it stay that way - I record that show for another family member - so I manually edited the timer to use the 7flix channel, destroying any chance of doing forensics on the cause of the anomaly. It recorded OK.
If it happens again for this week's episode of The Amazing Race I'll post back.
I also record the Amazing Race, but for reasons too convoluted to explain here, I record that with Media Centre. That has the name etc. It only has "new channel" on the Wiz
When you rescanned, did any of you get "duplicate" Seven channels in the Terrestrial TV LCN bouquet with LCNs 350 or more?
Quote from: csutak40 on March 04, 2016, 07:42:04 PM
...
Not sure if this has anything to do with it, but noticed that these two new channels have no icons. Don't see how that would cause this, just thought I'd mention it.
The changes in IceTV for these channels and the fact that the two channels have no picons have the same base cause: that both processes require information about some of the broadcast parameters of the new channels (what Daniel has been collecting in "Information needed for new channels (7flix, TEN HD and more)", and what I've been collecting in "Request for updates for channel picons" on the Beyonwiz forum). The key information is the same in both cases, though I collect it in a different way from the way Daniel asks for it to be collected. That's why I've been able to contribute information in "Information needed for new channels" in areas a long way from where I live, and why I haven't been able to contribute LCN information there, because my data collection method doesn't capture LCN information, because I have no need for it.
The picons for 7flix and TEN HD have been accepted into the Beyonwiz picon repository and should appear when you get the next Beyonwiz firmware update.
The missing picons in no way cause the "New channel" problem you're seeing, and the "New channel" problem doesn't cause the missing picons, though the two problems are not completely unrelated.
Quote from: csutak40 on March 04, 2016, 07:42:04 PM
Incidentally, I have two more questions. Is there a way of changing the size of the EPG on the TV? (see attached photo of the actual TV set, as opposed to looking at it on the Web)
I'm not quite sure what you mean: do you want to stop the EPG from being cut off at the edges, or do you want to change the font size, number of rows, or time span of the EPG data?
The EPG is almost certainly being cut off by overscan settings on the TV. Overscan is useful for some analog TV transmissions where there is distortion of the image near the edges. Overscan stretches the broadcast image so that the image is larger than the screen and the edges are cut off.
Many TVs allow you to turn off overscan using a setting named something like "Just Fit", "Screen Fit", "True Scan", "Full Scan". If it has that capability, set it to not stretch the image. The idea of these settings is to show the digital image exactly filling the screen (and you might wonder why the default is ever any different!).
If your TV doesn't allow you to turn off overscan (mine doesn't), or, if after turning overscan off, the EPG image doesn't fit the screen properly, you can adjust the position and size of the user interface overlay in MENU>Setup>AV setup>OSD position. Use Move Left/Right to increase the value (move right) until you see a bright band down the left of the TV screen, then decrease it until the bright band just disappears. Then reduce Width until a bright band appears on the right of the TV. Then increase it until the bright band just disappears. Then do the same with Move Up/Down and Height.
Now the EPG (and all teh user interface screens) will neatly fit the TV screen.
Quote from: csutak40 on March 04, 2016, 07:42:04 PM
Also, I seem to have acquired a bouquet called Melbourne. Has it got a purpose, before I get rid of it?
I don't know of a way of creating additional bouquets without the user actually asking for them to be created, and doing it that way, you'd have had to enter the bouquet name as "Melbourne". What's in the bouquet?
A scan for channels will create or replace the bouquets Last Scanned, Terrestrial TV LCN and Terrestrial RADIO LCN. It will also create empty Favourites (TV) and Favourites (Radio) if they don't already exist, but it won't change them otherwise. I've never heard of any other bouquet being created by a scan. If you've had a "Melbourne" bouquet in the past, restoring settings may have brought it back from a settings backup.
Quote from: prl on March 05, 2016, 01:29:52 PM
I'm not quite sure what you mean: do you want to stop the EPG from being cut off at the edges, or do you want to change the font size, number of rows, or time span of the EPG data?
Stop the EPG being cut off at the edges
Quote from: prl on March 05, 2016, 01:29:52 PMThe EPG is almost certainly being cut off by overscan settings on the TV. Overscan is useful for some analog TV transmissions where there is distortion of the image near the edges. Overscan stretches the broadcast image so that the image is larger than the screen and the edges are cut off.
Many TVs allow you to turn off overscan using a setting named something like "Just Fit", "Screen Fit", "True Scan", "Full Scan". If it has that capability, set it to not stretch the image. The idea of these settings is to show the digital image exactly filling the screen (and you might wonder why the default is ever any different!).
If your TV doesn't allow you to turn off overscan (mine doesn't), or, if after turning overscan off, the EPG image doesn't fit the screen properly, you can adjust the position and size of the user interface overlay in MENU>Setup>AV setup>OSD position. Use Move Left/Right to increase the value (move right) until you see a bright band down the left of the TV screen, then decrease it until the bright band just disappears. Then reduce Width until a bright band appears on the right of the TV. Then increase it until the bright band just disappears. Then do the same with Move Up/Down and Height.
Now the EPG (and all teh user interface screens) will neatly fit the TV screen.
I searched everywhere, can't see anything like this. FWIW if I look at the TV's EPG, that is sized correctly. It is only the T4's EGP that has the edges go too far
I found some settings on the TV's menu, changing those would change the size of the picture on the TV, but not on the Wiz. Then I found the OSD settings on the Wiz (see attached) I changed all of the numbers, it didn't seem to make any difference. I couldn't see a "bright band" regardless of what I changed the numbers to. That attached is back to the default numbers..
Quote from: csutak40 on March 04, 2016, 07:42:04 PM
Also, I seem to have acquired a bouquet called Melbourne. Has it got a purpose, before I get rid of it?
Quote from: prl on March 05, 2016, 01:29:52 PMI don't know of a way of creating additional bouquets without the user actually asking for them to be created, and doing it that way, you'd have had to enter the bouquet name as "Melbourne". What's in the bouquet?
A scan for channels will create or replace the bouquets Last Scanned, Terrestrial TV LCN and Terrestrial RADIO LCN. It will also create empty Favourites (TV) and Favourites (Radio) if they don't already exist, but it won't change them otherwise. I've never heard of any other bouquet being created by a scan. If you've had a "Melbourne" bouquet in the past, restoring settings may have brought it back from a settings backup.
It has what was in the original scan, I think. A friend set it up for me originally, he must have created it. Deleted it now. Incidentally, I don't have "Terrestrial RADIO LCN" either. Not that I need it :D
What make and model TV is it? I'll see if I can find an online manual and see if I can find out how to turn off overscan, because I'm pretty sure that's the problem.
I don't know why you couldn't adjust the PVR's user interface size using OSD position. I have used it to correct for overscan on our TV in just the way I described.
And, unless you've deleted it, your PVR does have the Terrestrial RADIO LCN bouquet. From live TV, press the RADIO button, and you'll see it. Ti get back to TV mode, go back out of the RADIO screen, press TV and select your usual bouquet in the usual way.
Quote from: prl on March 05, 2016, 10:37:19 PM
What make and model TV is it? I'll see if I can find an online manual and see if I can find out how to turn off overscan, because I'm pretty sure that's the problem.
I don't know why you couldn't adjust the PVR's user interface size using OSD position. I have used it to correct for overscan on our TV in just the way I described.
And, unless you've deleted it, your PVR does have the Terrestrial RADIO LCN bouquet. From live TV, press the RADIO button, and you'll see it. Ti get back to TV mode, go back out of the RADIO screen, press TV and select your usual bouquet in the usual way.
It is Sony KDL-46EX520 https://www.google.com.au/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0ahUKEwiHrMKp96nLAhXDF5QKHQGfCwQQFggeMAA&url=http%3A%2F%2Fwww.tv-manual.com%2Fmanuals%2Fsony0%2FSony_KDL-46EX520_manual.pdf&usg=AFQjCNHJM_8SytNrUgzpGe_a65Zf85ANqQ&sig2=XAcdfQjGBf_W15kkw9EgGA&cad=rjt (https://www.google.com.au/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0ahUKEwiHrMKp96nLAhXDF5QKHQGfCwQQFggeMAA&url=http%3A%2F%2Fwww.tv-manual.com%2Fmanuals%2Fsony0%2FSony_KDL-46EX520_manual.pdf&usg=AFQjCNHJM_8SytNrUgzpGe_a65Zf85ANqQ&sig2=XAcdfQjGBf_W15kkw9EgGA&cad=rjt)
You are right about the Terrestrial Radio. I was just looking at the list shown when I press EPG, never pressed the Radio button (or the TV, for that matter)
I WILL have to do something about this remote! As I said, I had it in the bedroom and hardly used it there, watched things on the TV through the network. Now that it is in the loungeroom I realising what a horrible remote it is. When I'm sitting in my chair, which is a bit side on from the Wiz, it doesn't work at all (the Toppy has no problems) So, I have to move to the couch, to sit directly opposite and even then it doesn't work half the time. As I'm yet to familiarise myself with it, I' never sure if I pressed the wrong button, or it just didn't "take". I usually find it to be the latter. I have an old Harmony 785 remote that I stopped using years ago, may have to get it out to see if it is an improvement on this.
Sorry, just tested the link I've sent and it doesn't work. Not sure why. I just Googled KDL-46EX520_Manual and got that link, which worked for me Maybe try this way https://www.google.com.au/search?q=KDL-46EX520_Manual&ie=utf-8&oe=utf-8&gws_rd=cr&ei=ZwnbVpyJK4rG0ATfl4nACg#newwindow=1&q=KDL-46EX520+Manual (https://www.google.com.au/search?q=KDL-46EX520_Manual&ie=utf-8&oe=utf-8&gws_rd=cr&ei=ZwnbVpyJK4rG0ATfl4nACg#newwindow=1&q=KDL-46EX520+Manual)
I've found the setting I was looking for in the TV manual (I just searched for "Sony KDL-46EX520 manual" in Google).
I'm not sure how the manual maps to what you actually do on the TV, but what I was looking for is in the manual in:
Settings/Home Menu>Picture & Display>Screen (for inputs other than a PC)>Display Area. Set Display Area to "Full Pixel". If that's not available, try "+1".
When you set that on the TV, the EPG may not fill the whole screen. If that's the case, you may need to adjust the GUI overlay sixe and position in OSD position as in my earlier post.
The "bright bands" I was talking about in the GUI size adjustment look like the attached image (band on the left edge where light grey shows through with the two black "5" numbers showing). Apologies for the image quality.
Quote from: csutak40 on March 06, 2016, 03:26:43 AM
...
I WILL have to do something about this remote! As I said, I had it in the bedroom and hardly used it there, watched things on the TV through the network. Now that it is in the loungeroom I realising what a horrible remote it is. When I'm sitting in my chair, which is a bit side on from the Wiz, it doesn't work at all (the Toppy has no problems) So, I have to move to the couch, to sit directly opposite and even then it doesn't work half the time.
That's mainly due to the sensitivity, masking and positioning of the IR receiver in the T3 and T4. Changing to a different remote won't help much with that problem.
Quote from: csutak40 on March 06, 2016, 03:26:43 AM
I have an old Harmony 785 remote that I stopped using years ago, may have to get it out to see if it is an improvement on this.
We use a Harmony 785 with our in-use T4. I use a T3 remote on my test T2, T3 & T4, unless I want to test something specific to the T2 or T4 remote.
Using the Harmony remote doesn't help with the narrow range of angle where the remote works, but it is a clean way for use to interact with our AV setup.
This is still a problem..
I just looked in the EPG listings and it is not marked there as being recorded. I also did a search in EPG for "Once upon a time" and it found TWO listings. One for 7flix and another for "New Channel". So, I went right through the Terrestrial EPG, to see if I can find an extra listing for "New Channel", no such luck.
So, I am completely lost as to what causes this and how to fix it
Before posting things, I again deleted the timer completely from IceTV, reloaded the timers to the Wiz, restarted it, set the timer again, etc. Nothing changed
You need to do a re-scan that clears all the old channels. Only then will you be able to get this all working properly.
In MENU>Setup>Tuners>Manual scan, set "Type of scan" to "Complete", set "Region" to your normal Location Scan region (it should default to the value for the last region scan you did) and set "Clear before scan" to "yes".
Then press OK to start the scan. When the scan completes, press OK again to accept the scan.
That will take you back to MENU>Setup>Tuners. Go back into Manual scan, and repeat the scan using the same values. I don't know the reason for the second scan, but peteru recommends it on the Beyonwiz forum. It will do no harm, anyway.
This time, when the scan completes, press OK to accept the scan, and the press EXIT until you get back to Live TV.
You should now have a clean set of channels scanned in the bouquets Last Scanned and Terrestrial TV LCN.
If you use Favourites, go into your favourites list and delete any "New Channel" entries, and any entries that don't take you to the correct (or any) channel. When that's done, add back any "real" channels you deleted, and an add any new channels (like 7flix) that aren't in the Favourites.
Then MENU>Plugin>IceTV>Disable IceTV. Then MENU>Plugin>IceTV>Enable IceTV. Then MENU>Plugin>IceTV>Fetch EPG and update timers now.
Has that helped?
Quote from: prl on March 12, 2016, 01:06:27 PM
Has that helped?
Thank you for all the trouble you went to, but I'm afraid it hasn't. It has changed, in that it no longer says "new channel" it is just blank. Also when I now search for the show, it only finds one instance, not two, as before.
I followed all of the instructions carefully, in fact I then went back and repeated the last bit, restarted the GUI after disabling IceTV and again after re-enabling it.
If you create a new IceTV recording on 7flix, does the timer get the correct channel?
I didn't say that doing the rescan would fix everything, just that the IceTV problems couldn't be sorted out until you'd done a clean scan.
Quote from: csutak40 on March 05, 2016, 09:43:30 PM
I found some settings on the TV's menu, changing those would change the size of the picture on the TV, but not on the Wiz.
On your Sony TV did you go to "Settings > Set-up > Screen Settings > Display Area" and select the "Full pixel" option?
The setting may only apply to the HDMI input you are viewing so make sure you are watching the Beyonwiz when you set the "Full pixel" option.
Quote from: csutak40 on March 05, 2016, 09:43:30 PM
Then I found the OSD settings on the Wiz (see attached) I changed all of the numbers, it didn't seem to make any difference. I couldn't see a "bright band" regardless of what I changed the numbers to.
As you decrease the Width the right hand side of the picture moves inwards. If you go far enough you will see a white band appear on the right side.
You would then increase the "Move Left/Right" setting to move the whole image to the right, to centre it.
At this if you end up with a white band on both sides you have made the width too small. So you would increase the Width a little bit then decrease the "Move Left/Right" a little bit.
After getting the width correct you need to adjust the Height and "Move Up/Down"position until the circle in the middle looks perfectly round.
You can use the ruler scales to centre the image.
Attached screenshot shows grey band on right side.
Quote from: prl on March 06, 2016, 11:12:18 AM
Quote from: csutak40 on March 06, 2016, 03:26:43 AM
I WILL have to do something about this remote! As I said, I had it in the bedroom and hardly used it there, watched things on the TV through the network. Now that it is in the loungeroom I realising what a horrible remote it is. When I'm sitting in my chair, which is a bit side on from the Wiz, it doesn't work at all (the Toppy has no problems) So, I have to move to the couch, to sit directly opposite and even then it doesn't work half the time.
That's mainly due to the sensitivity, masking and positioning of the IR receiver in the T3 and T4. Changing to a different remote won't help much with that problem.
The other day I noticed my LCD display in my T4 has moved or warped. The bottom right corner of the display is noticeably back further from the front perspex then the top left corner. I don't know where the IR sensor is located (top-right corner maybe) but I can point my T3 remote way at the ceiling, or at the walls to the left or right or behind me and the T4 still responds. The only time it doesn't receive the signal is if I point the remote below the T4.
Quote from: prl on March 12, 2016, 01:06:27 PM
Go back into Manual scan, and repeat the scan using the same values. I don't know the reason for the second scan, but peteru recommends it on the Beyonwiz forum.
You should now have a clean set of channels scanned in the bouquets Last Scanned and Terrestrial TV LCN.
When I did a manual 'complete' scan with region Sydney and 'Clear before scan' enabled it kept the Terrestrial TV LCN file without adding the new channels to it. Maybe this be why peteru recommends to repeat the scan.
Quote from: prl on March 12, 2016, 11:34:14 PM
If you create a new IceTV recording on 7flix, does the timer get the correct channel?
I didn't say that doing the rescan would fix everything, just that the IceTV problems couldn't be sorted out until you'd done a clean scan.
Eureka!!!!
Just set a timer and it worked! I misunderstood. I thought that disabling and re-enabling iceTV would force it to re-send the timer, hence fix the missing channel name. So does this mean that if I delete that timer and re-set it, it should now work?
Quote from: csutak40 on March 13, 2016, 01:53:05 AM
Eureka!!!!
Just set a timer and it worked! I misunderstood. I thought that disabling and re-enabling iceTV would force it to re-send the timer, hence fix the missing channel name. So does this mean that if I delete that timer and re-set it, it should now work?
If you disable and re-enable iceTV it will wait until '15 minutes since the last fetch' before it does a fetch. After re-enabling IceTV you should click on "Fetch EPG and update timers now' to force a fetch right away.
If you delete the timer you should wait 20 minutes before recreating the timer.
If IceTV cannot delete the timer with the dodgy name you may end up with 2 timers: 1 with the correct name and 1 with the incorrect name. If that happens just delete the dodgy timer from the T4 's timer list.
Quote from: Dave at IceTV on March 13, 2016, 12:22:04 AM
On your Sony TV did you go to "Settings > Set-up > Screen Settings > Display Area" and select the "Full pixel" option?
The setting may only apply to the HDMI input you are viewing so make sure you are watching the Beyonwiz when you set the "Full pixel" option.
Hmm. That setting only has three options "normal", +1 & -1. Oh, just discovered +1 actually improved it. Not perfect, but a lot better. The word "Favourites" is visible except for half the F.
Also discovered that if I change the Vertical Size to the minimum, it fixes that problem
Quote from: Dave at IceTV on March 13, 2016, 12:22:04 AM
As you decrease the Width the right hand side of the picture moves inwards. If you go far enough you will see a white band appear on the right side.
I will fiddle with that manana :-) Thank you
Quote from: Dave at IceTV on March 13, 2016, 12:36:38 AM
The other day I noticed my LCD display in my T4 has moved or warped. The bottom right corner of the display is noticeably back further from the front perspex then the top left corner. I don't know where the IR sensor is located (top-right corner maybe) but I can point my T3 remote way at the ceiling, or at the walls to the left or right or behind me and the T4 still responds. The only time it doesn't receive the signal is if I point the remote below the T4.
So, I need to figure out how to damage the LCD display? ;D
Quote from: Dave at IceTV on March 13, 2016, 12:22:04 AM
As you decrease the Width the right hand side of the picture moves inwards. If you go far enough you will see a white band appear on the right side.
You would then increase the "Move Left/Right" setting to move the whole image to the right, to centre it.
At this if you end up with a white band on both sides you have made the width too small. So you would increase the Width a little bit then decrease the "Move Left/Right" a little bit.
After getting the width correct you need to adjust the Height and "Move Up/Down"position until the circle in the middle looks perfectly round.
You can use the ruler scales to centre the image.
Attached screenshot shows grey band on right side.
Decided to play with it, after all. I don't know what I'm doing wrong, but regardless of how much I move the numbers, the screen doesn't move. I went from 0 to 720, which is the limit. Incidentally, the screen looks different on the TV then it does on the screen shot from the Web (see attached)
LOL, after fiddling for ages to get the attachments small enough to fit, I now realise that one is only allowed four of them, so will have to sent two as a PS :-)
P.S.
Quote from: Dave at IceTV on March 13, 2016, 12:36:38 AM
...
The other day I noticed my LCD display in my T4 has moved or warped. The bottom right corner of the display is noticeably back further from the front perspex then the top left corner.
There's a known problem with some of the earlier batches of T4s that the glue holding the display onto the front panel PCB in place gives way and the display no longer sits in the right place.
But that shouldn't affect the IR detector, which is soldered onto the front panel PCB, unless the moved display is partly obscuring the IR detector.
The front panel PCM is fairly securely screwed onto the front panel mounding, including by the three (on the T4) screws that act as sensors for the tree touch buttons.
Quote from: Dave at IceTV on March 13, 2016, 12:36:38 AM
I don't know where the IR sensor is located (top-right corner maybe) but I can point my T3 remote way at the ceiling, or at the walls to the left or right or behind me and the T4 still responds. The only time it doesn't receive the signal is if I point the remote below the T4.
The IR detector is on the right-hand side of the central clear plastic panel, at about the same height as the centres of the touch button silkscreening. It has its own circular window in the black paint on the inside of the clear panel. I think that the fact that the IR has its own fairly small window contributes to the fairly small angular range of the IR control on the T4 (and also on the similarly laid-out T3). The T2's IR detector simply sits in the larger window where the display would be if the T2 had one.
Quote from: csutak40 on March 13, 2016, 03:48:33 AM
... Incidentally, the screen looks different on the TV then it does on the screen shot from the Web (see attached) ...
The adjustment screen is one where the view in OpenWebif gram screenshot is different from the actual screen. If you want to post views of the adjustment screen that show what's actually displayed, unfortunately you need to use a camera, not OpenWebif to show what's actually on the TV screen.
This is also true for screens like the EPG, where your screen photo clearly shows the EPG being cut off at the left, while your OpenWebif grem screenshot view shows the whole EPG correctly.
And by the way, setting either Width or Height to 0 in the adjustment screen is never going to do anything useful. Setting move Left/right to 720 isn't a useful value, either.
The setup I have for my TV, which has built-in overscan that can only be increased in the TV, and not decreased, is:
Width=692
Move Left/Right=14
Height=552
Move Up/Down=13
The numbers that are right for your TV will be different, but not wildly different like 720 for Move Left/Right and 0 for Width as in the screenshots you posted.
Beyonwiz P2
OK - as an addendum to all this - talking about screen resolutions and what fits and what doesn't - the display of my EPG has/had always been wildly out.
The display of the day name at the left side would display as "day" and the rest would be off to the left.
No amount of fiddling with the OSD setting would make a pixel of difference, from the min to the max, or anywhere in between, as described by Judy.
It wasn't until I saw "prl"s suggestion, some time back, that the setting on the TV should be changed, that I had some success. My TV is an LG LB6500 and the display setting that did the trick was "Just scan" - that brought the edges of the screen display into view and the EPG displayed perfectly. (also "cinema zoom 1-16 using setting 1 brought ALL edges back in to display the whole picture).
As Judy said, and prl explained , the webif screen display showed it as being perfect.
However, I repeat, I repeat, that the fiddling with the settings on the Beyonwiz made ABSOLUTELY no difference to the display screen in the OSD settings, and therefor no difference to the EPG display.
Quote from: mac37 on March 13, 2016, 01:15:53 PM
...
However, I repeat, I repeat, that the fiddling with the settings on the Beyonwiz made ABSOLUTELY no difference to the display screen in the OSD settings, and therefor no difference to the EPG display.
That's very strange, and I have no idea why it would be that way, but it does also seem to be what's happening with Judy's TV.
Quote from: prl on March 13, 2016, 12:43:38 PM
And by the way, setting either Width or Height to 0 in the adjustment screen is never going to do anything useful. Setting move Left/right to 720 isn't a useful value, either.
The default
is 0 (and 720) The second picture I've attached in my post abvove show the default. I started off with that then watched as I was changing the numbers and nothing moved
I will take more photos and send them
Quote from: mac37 on March 13, 2016, 01:15:53 PM
It wasn't until I saw "prl"s suggestion, some time back, that the setting on the TV should be changed, that I had some success. My TV is an LG LB6500 and the display setting that did the trick was "Just scan" - that brought the edges of the screen display into view and the EPG displayed perfectly. (also "cinema zoom 1-16 using setting 1 brought ALL edges back in to display the whole picture).
I did fiddle with the TV last night, but (except for some settings that made the picture tiny, with huge borders around-envelope, or other weird sizes) none of the settings I could find gave the desired result
Quote from: csutak40 on March 13, 2016, 05:32:11 PM
Quote from: prl on March 13, 2016, 12:43:38 PM
And by the way, setting either Width or Height to 0 in the adjustment screen is never going to do anything useful. Setting move Left/right to 720 isn't a useful value, either.
The default is 0 (and 720) The second picture I've attached in my post abvove show the default. I started off with that then watched as I was changing the numbers and nothing moved
...
The default for Width is 720 and the default for Left/Right is 0. I never said otherwise. But you posted OpenWebif screenshots that show Width as 0 and Left/Right as 720 (screenshot1.jpg) and Width as 720 and Left/Right as 720 (screenshot2.jpg). They are the values I was referring to and they are not sensible choices for those settings.
Unfortunately those screenshots aren't able to show what was actually on the TV screen at the time.
From your other posts and screenshots, I think I can see the problem, but I really don't know why you can't adjust the screen overlay appropriately on the TV.
Quote from: Dave at IceTV on March 13, 2016, 02:15:15 AM
If you disable and re-enable iceTV it will wait until '15 minutes since the last fetch' before it does a fetch. After re-enabling IceTV you should click on "Fetch EPG and update timers now' to force a fetch right away.
If you delete the timer you should wait 20 minutes before recreating the timer.
If IceTV cannot delete the timer with the dodgy name you may end up with 2 timers: 1 with the correct name and 1 with the incorrect name. If that happens just delete the dodgy timer from the T4 's timer list.
Hooray! I deleted the timer last night, then completely forgot about it. Just re-created it. I now have 7flix showing! It deleted the old timer by itself
Quote from: prl on March 13, 2016, 12:09:55 PM
Quote from: Dave at IceTV on March 13, 2016, 12:36:38 AM
The other day I noticed my LCD display in my T4 has moved or warped. The bottom right corner of the display is noticeably back further from the front perspex then the top left corner.
There's a known problem with some of the earlier batches of T4s that the glue holding the display onto the front panel PCB in place gives way and the display no longer sits in the right place.
Good to know it's not just my T4.
Quote from: prl on March 13, 2016, 12:09:55 PM
The T2's IR detector simply sits in the larger window where the display would be if the T2 had one.
When the late afternoon sun shines on the front of my T2 the transparent black front plastic might as well be clear because I can see the circuit board inside and it cheapens the T2 experience. Beyonwiz could have stuck a black sticker on the inside (with a hole for the IR sensor).