Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - sam

#1
General Discussions / Re: IceTV Resurrected
November 14, 2015, 07:18:32 PM
Quote from: warkus on October 25, 2015, 06:54:50 PM
Sam,

I have a Skippa here in the office doing exactly that at the moment. It lasts between 30 seconds and 5 minutes on boot before freezing, audio still running but frozen other than that and occasionally reboots itself automatically.

I am 80% sure it's a faulty SOC (main controller). Freeze spraying the heat sink on the SOC keeps it up for an indefinite period, most I've had it up is 15mins. As soon as I stop spraying the heat sink, it locks within a very short time.

If it is a faulty SOC, it's a bin job, simple. I'm really sorry.

I haven't finished testing yet but once I've finished I will post confirmation either way...

Mark

Hi Mark,

Do you have any update on your testing please? Whether this is a faulty SOC and therefore a bin job for my Hot faulty D.O.A SKIPPA (which was to be replaced), that Freezes. At least I could get it to boot up after replacing the Power Pack, but you can't use SKIPPA and it's currently packed in its box and stored away - Out of my sight - out of my frustration range!   

I wish it was repairable as when it is up and running it shows great potential.

Regards,
SAM
#2
General Discussions / Re: IceTV Resurrected
October 25, 2015, 08:12:57 PM
Quote from: warkus on October 25, 2015, 08:04:42 PM
It's not too late, you have 180 days with PayPal, and my calculations from May 25 it's not 180 days yet...

Mark

Ok thanks Mark, I just checked how many days and its 126 since payment...  I'll give PayPal a try.

Sam
#3
General Discussions / Re: IceTV Resurrected
October 25, 2015, 07:59:50 PM
Quote from: warkus on October 25, 2015, 06:54:50 PM
Sam,

I have a Skippa here in the office doing exactly that at the moment. It lasts between 30 seconds and 5 minutes on boot before freezing, audio still running but frozen other than that and occasionally reboots itself automatically.

I am 80% sure it's a faulty SOC (main controller). Freeze spraying the heat sink on the SOC keeps it up for an indefinite period, most I've had it up is 15mins. As soon as I stop spraying the heat sink, it locks within a very short time.

If it is a faulty SOC, it's a bin job, simple. I'm really sorry.

I haven't finished testing yet but once I've finished I will post confirmation either way...

Mark

Thanks Mark, I'll wait in fairyland hope... that it is not a faulty SOC. 😪
This SKIPPA was being replaced but the replacement never arrived :(
What a bummer! 

And too late to claim on my credit card / PayPal as I paid on the first day SKIPPA was announced.

Sam
#4
General Discussions / Re: IceTV Resurrected
October 25, 2015, 06:16:10 PM
Quote from: sam on October 22, 2015, 07:04:24 PM
Quote from: warkus on October 22, 2015, 06:30:07 PM
All good...

WOW that price is shocking... (really sorry to say Sam - apologies)

I realise there is a markup on these things but that is over DOUBLE what i sell em for...

I need to up my price, lol...

Yeah I know the price is/was a shocker, & I really didn't want to spend anymore on SKIPPA.
I was going to purchase through you but was so desperate and impatient to try to get SKIPPA at least booting up, that I rushed off to Jaycar & grabbed one as posting to me was going to take a few days :(

Cheers,
Sam

Hi Warkus / Mark,

Unfortunately the new $64.94 PowerPack has not fixed the SKIPPA freezing problems :(.
It helped with at least being able to Boot up SKIPPA.
But SKIPPA only works for approx. 10 - 15 mins before it freezes completely & is unresponsive. Frozen picture on the TV with live audio playing. I have to pull the power plug to shut it down.

I feel this SKIPPA is repairable, when it works it looks great - but how more money do I have to spend on this SKIPPA? :(
It has always run very hot, and even gets hot in Standby - I suspect HDD is probably still running.
My TEAC HDB850 PVR is always cool even when being used (I realise it does not have a internal HDD, it uses a USB drive for recording).

I'm suspecting now that 'perhaps' there is a faulty cable connection to the HDD.

Mark, if you think its worth you looking at my SKIPPA would you please message me and I will give you my contact email address.
Thanks,
Sam




#5
General Discussions / Re: IceTV Resurrected
October 22, 2015, 07:04:24 PM
Quote from: warkus on October 22, 2015, 06:30:07 PM
All good...

WOW that price is shocking... (really sorry to say Sam - apologies)

I realise there is a markup on these things but that is over DOUBLE what i sell em for...

I need to up my price, lol...

Yeah I know the price is/was a shocker, & I really didn't want to spend anymore on SKIPPA.
I was going to purchase through you but was so desperate and impatient to try to get SKIPPA at least booting up, that I rushed off to Jaycar & grabbed one as posting to me was going to take a few days :(

Cheers,
Sam
#6
General Discussions / Re: IceTV Resurrected
October 22, 2015, 06:22:09 PM
Quote from: warkus on October 22, 2015, 05:41:46 PM
2.5mm plug is the WRONG plug for the Skippa.

The plug is a 2.1mm Positive tip.

I hope that was just a typo...

OMG I'm So sorry Warkus - My Bad! :(
it is a 2.1mm plug centre positive!
Sam
#7
SKIPPA / Re: Skippa IR Remote
October 22, 2015, 05:27:26 PM
Quote from: pnkoshea on September 28, 2015, 05:59:38 AM
Hi Guys,

Can I ask what manufacturer & model code you used to get the Harmony to work?  I tried to set up my Harmony 200 and was nt able to find a manufacturer/model code that worked (Al Tech PVR9600 didn't) and then the Harmony would not register the Skippa's IR beam for manual configuration.

Any/All help appreciated!!

Cheers,
Rick

Hi Rick,

I have a Harmony 650 Universal Remote and have setup SKIPPA. The 'MyHarmony' setup accepted Manufacturer: IceTV DVR

Hope that helps you.
Cheers,
Sam
#8
General Discussions / Re: IceTV Resurrected
October 22, 2015, 04:58:19 PM
Quote from: TimC on October 21, 2015, 08:56:25 PM
I saw something somewhere that some plugpacks were off voltage an causing problems. 

It may be worth buying an equivalent off the shelf plugpack and trying it.

Have a look in some of the "freezing" bug reports for where it was discussed.

Hi TimC
I took your suggestion and purchased a new Power Supply from Jaycar Electronics a 12VDC 5A Desktop Power Supply - Fixed 2.5mm plug.  PSU SMPS IEC 12VDC 5A-PLGS $64.94 :(
Plugged the Powerpack into Power & connected to SKIPPA.
SKIPPA Booted quickly & I was then able to use the Remote Control to move around through the Menu to check and change Settings.

The Remote was responsive to commands & I did not experience any Freezing (which is the first time)! I was able to put SKIPPA in Standby when I wanted to end the session, using the Standby button on the Remote (again this is the first time).

I'll test more later today & check that my programs set to Record tonight DO Record. SKIPPA has not been able to record any of my set programs - I have not been able to use SKIPPA at all until today.

So looking little more positive so far, and is indicating that the original Power Supply Adaptor was faulty. I'll wait and see...

Thanks TimC for suggesting that the Power Supply could be at fault.
Sam
#9
General Discussions / Re: IceTV Resurrected
October 22, 2015, 04:32:54 PM
Quote from: Dave at IceTV on October 22, 2015, 02:29:34 PM
Quote from: sam on October 21, 2015, 05:29:34 PM
Hi Dave,

As I have a faulty SKIPPA that will not fully Bootup or work. IceTV were sending a Replacement SKIPPA before IceTV was put into Voluntary Administration. But it was never delivered to me!
You should contact PayPal (see the PayPal thread) or your credit card provider to get a refund as your skippa will never work without some help from UEC.

Quote from: sam on October 21, 2015, 05:29:34 PM
How can I update the Firmware via USB when my SKIPPA won't finish boot up?
The circle is frozen, it never finishing loading - the circle disappears to a blank/black screen  - pressing Menu on the remote control does nothing.
If you have another device or laptop with the same type of power supply (12V 4A and the same plug) you try another power supply to see the skippa will then boot up.

If it gets to the IceTV logo screen (it comes after the loading... circle) you can try a sequence of button presses to reset the skippa, or reset and format the hard drive.

The following will reset and format the HDD.

1. Unplug the power cable from the back of the Skippa.
2. Wait 10 seconds.
3. Plug the power cable back in.
4. On the TV screen, when you see the loading screen vanish press the following remote control buttons in this order:
  - Red, Green, Yellow, Blue, Yellow
5. The Skippa will should restart and run through the initial setup process again.

The opposite resets without formatting the HDD: Blue, Yellow, Green, Red, Green.

There may be another combination that installs the firmware from USB, or maybe they use a computer app connected via Serial-to-USB.

Thanks Dave,
I did manage to boot SKIPPA to Recovery using a little different order to your colour combination as I mentioned in my reply to Ian above :)

Connected SKIPPI into Power to start SKIPPA, when the boot screen appeared (Round Blue circle) I quickly pressed the remote keys in the following order : red, green, yellow, blue, yellow .
This should Reboot SKIPPA  - It did not reboot on my first try, so I continued pressing the red, green, yellow, blue, yellow while still on the splash screen until the SKIPPA eventually rebooted.

I won't repeat the results are in my reply above to Ian.

Thanks for your advice Dave, it's always greatly appreciated. It's good to have you BACK!
Sam


#10
General Discussions / Re: IceTV Resurrected
October 21, 2015, 08:48:07 PM
Quote from: IanL-S on October 21, 2015, 05:36:17 PM
Sam
Some PVRs have a special procedure to do the recovery. Do a www search for procedure to recover Altech PVRs.

Ian


Thanks Ian. I couldn't find much with online search, but I did try this:

Connected SKIPPI into Power to start SKIPPA, when the boot screen appeared (Round Blue circle) I quickly pressed the remote keys in the following order : red, green, yellow, blue, yellow .
This should Reboot SKIPPA  - It did not reboot on my first try, so I continued pressing the red, green, yellow, blue, yellow while still on the splash screen until the SKIPPA eventually rebooted.

It had reset back to 'out of the box' and I was able to do part of setup before a freeze, the Remote was unresponsive to any key press. Eventually after numerous Freezes and having to manually Boot SKIPPA (pull the plug wait a min. replug) I got my Network & IceTV Account setup.

I also was able to then Update the Software from the USB Stick. SKIPPA rebooted after update was successfully installed.
All was showing promise at this stage, and SKIPPA rebooted and live TV played. I thought I was winning... until SKIPPA froze again. I had to unplug it to shutdown.
I left it unplugged to cool down for awhile, then replugged to boot up, it goes through it process until "RUNNING VIDEO PLAYER" ... Loading and that's as far as it gets.
So I unplugged and will leave it for tonight.

I know it has connected to my IceTV online account as I received an email from IceTV Support - "IceTV has received a notification from your video recorder that it was unable to record one of your shows due to an error". The email came through today, the shows mentioned were yesterday, when I had SKIPPA unplugged.

Perhaps another Software Update might fix my faulty SKIPPA? I certainly hope so, but I do feel this is a Hardware fault (as IceTV Support suggested originally) -not Firmware.

Thanks again for your help.
Sam
#11
General Discussions / Re: IceTV Resurrected
October 21, 2015, 05:29:34 PM
Quote from: Dave at IceTV on October 18, 2015, 04:34:27 PM
Quote from: bodogbodog on October 18, 2015, 03:40:15 PM
At this stage I suspect for most of us a new firmware release that provides stability is what we're really after

For those looking for a firmware update to fix their Skippa's issues see:
http://support.icetv.com.au/entries/97066117-How-to-update-the-software-from-a-USB-stick

Hi Dave,

As I have a faulty SKIPPA that will not fully Bootup or work. IceTV were sending a Replacement SKIPPA before IceTV was put into Voluntary Administration. But it was never delivered to me!

How can I update the Firmware via USB when my SKIPPA won't finish boot up?
The circle is frozen, it never finishing loading - the circle disappears to a blank/black screen  - pressing Menu on the remote control does nothing.

So I'm unable to follow the instructions  in 'How to update the software from a USB stick'.
Scroll down to Settings and press OK etc...

I copied the "upgrade_skippa.ice" file onto a USB stick & inserted into a USB port at the rear of SKIPPA on the 'off chance' this might somehow force SKIPPA to finish boot up.

Kind Regards,
Ronni
#12
General Discussions / Re: IceTV Resurrected
October 18, 2015, 01:50:43 PM
Quote from: Paul55 on October 18, 2015, 12:19:59 PM
Quote from: jim szabo on October 18, 2015, 12:16:59 PM
Hi Dave i contacted 'mark.everingham@tphinsolvency.com.au' as you suggested with no reply & contacted David Dargie from NAS Australia for a replacement SKIPPA who was unable to help.
My question is what do i do with a faulty Skippa
regards Jim Szabo :-[

I think your only option now is to wait until the administration process is complete. Or maybe you could contact UEC, the company that is holding the Skippas - though I'd be surprised if they were any help.
-----
Hi Dave,

I also have a faulty SKIPPA that will not fully Boot or work and was to receive a Replacement SKIPPA before IceTV was put into Voluntary Administration.
Quote from IceTV Customer Support below:

Leon (IceTV Customer Support)
Oct 3, 1:54 PM
Hi Ronda,
Thank you for contacting IceTV Customer Service.
Sorry to hear you are having a problem with your new SKIPPA!
We are replacing some SKIPPA's that have similar problems which appear to actually be a hardware fault (and not a firmware issue), we will send you a reply paid postal order and replace your SKIPPA at the same time, this will probably only happen towards the end of next week however due to the long weekend getting in the way of the postal service.
Best Regards,
Leon 
IceTV Support Team
IceTV Pty Limited
Level 1/20 Chandos Street, St Leonards, NSW 2065
/End Quote:

I again contacted IceTV Support when the Replacement Skipper did not arrive and was advised by you Dave to contact  'mark.everingham@tphinsolvency.com.au'. Which I did as you suggested but again I also have had NO reply from Mr Everingham.

So, unless a Firmware Update which IceTV Support have indicated won't fix my SKIPPA as its a Hardware fault, can get my SKIPPA to function - I really can't use my IceTV Recording account. I've given all my EyeTV Elgato units away as I was not going to need them once I had SKIPPA :(

Kind Regards,
Ronni