Problems with 9Go and 9Go HD

Started by Ian_AW, November 25, 2024, 02:59:39 PM

Previous topic - Next topic

Ian_AW

G'day,

I have a Beyonwiz T2 and an IceBox with 4 tuners and am getting odd things with the EPG.

On the T2, I get 9Go on Channel 99, but on the IceBox I do not see anything about 99, but there is 93 only it is all blank. It is identifies as 9Go. Switching live TV to 93 gets me a blank screen.

The units are less than 50 mm apart and I have gone through the usual things like having just one connected and getting exclusive use of the antenna. The Internet is available to both via wired Ethernet and a 100/20 FTTP NBN connection.

How can I get 9Go?

IanL-S

#1
If you have the latest firmware (12.1.1) you should be seeing both SD and HD "versions" of 9Go! Well, maybe not. I only have the HD version (LCN 93) [BYOB1]. But I have both the SD and HD "versions" of 9Gem. On BYOB2 and My IceTV IceBox LCN is shown as not active - but is described as (Go! Melbourne HD, which is clearly incorrect!). I did a soft reset for both after installing 12.1.1 so not sure why BYOB1 is different.

If you wish, it is possible to check what is happening using the TVHeadend web server (accessed by http://{IP address of your IceBox}:9981/) and select Configuration > Channel EPG > Channels.

IPDATE: Got things a bit confused actually (Go! SD is on LCN 93 and 9G! HD is on LCN 99), so there is something amiss with my setup which   
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Ian_AW

I am running the latest firmware. I was automatically updated. I did a power cycle.

I will check the TVHeadend bit a little later.

Thanks

IanL-S

OK, there was no need to do a soft-reset when installing 12.1.1. unless (like me) you were running the 12.1.1 beta and had to revert to the then current public firmware before updating.

As I said in the addendum to my prior post there is something very odd in my set which I will look at tomorrow. It is always possible I got this completely confused as it has been a long ay and I have spent the last hour and three quarters waiting to talk to my bank about a minor problem I had in transition to new platform.
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Daniel Hall at IceTV

Quote from: Ian_AW on November 25, 2024, 02:59:39 PMG'day,

I have a Beyonwiz T2 and an IceBox with 4 tuners and am getting odd things with the EPG.

On the T2, I get 9Go on Channel 99, but on the IceBox I do not see anything about 99, but there is 93 only it is all blank. It is identifies as 9Go. Switching live TV to 93 gets me a blank screen.

The units are less than 50 mm apart and I have gone through the usual things like having just one connected and getting exclusive use of the antenna. The Internet is available to both via wired Ethernet and a 100/20 FTTP NBN connection.

How can I get 9Go?

Hi Ian,

Firstly I would recommend disabling 9Go! on 93 in your account settings on the IceTV website as there is no need for both channels as 9Go! HD on 99 is an MPEG-4 HD channel now.

At this point you have two options, one would be to look at manually mapping within the TVHeadEnd web interface, and on the page that Ian mentioned above you can look under the "EPG Source" where you can manually change what IceTV channel each of the scanned in channels. If you do change an EPG Source on this page ensure that you click on "Save" at the top of the page and then reboot the IceBox to have it download a fresh set of guide data.

The second is a soft reset as it will re-scan the channels in for you and also automatically map the channels that you have under your account.
Regards,

Daniel.
CTO.

Ian_AW

Thanks Daniel and Ian.

I decided to try the TVHeadend path and edited the link provided.

The EPG now shows LCN 99 and no LCN 93, however it is still empty.

TVHeadend shows the EPG Source as blank.

Another interesting thing is that when the EPG is called on the IceBox, the label for LCN 99 is bright yellow.

So it looks like a soft reset, only I have to wait until there is a suitable break in my regular recording.

Is there any other thing to try?

Thanks.

raymondjpg

Quote from: Ian_AW on November 26, 2024, 03:17:40 PMTVHeadend shows the EPG Source as blank.
1. Double left mouse click on the empty entry on the EPG source for 9Go!, click down arrow and select the box next to the source 9Go! then left click on another row and you should see the 9Go! as EPG entry in the EPG source row you originally selected. Then hit the Save button, first item in row directly above the table.

2. Reboot IceBox to download a fresh set of guide data.

Beyonwiz T2, Beyonwiz U4, IceBox BYO with Hauppauge WinTV-dualHD (x2), Hauppauge WinTV-quadHD

Ian_AW

Well, that didn't go down well.

Did a soft reset and now have  a heap of LCNs starting with 100... and no sound.

IanL-S

Not sure about the sound problem, but @Danial Hall says the way to fix the LCN numbers is to watch live TV on one "channel" from each network that has incorrect LCN for a couple of minutes and the LCNs correct themselves. I have tried it and it works a treat.
Ian
IceTV: IceBox + BYOB IceBox + 2xTRF-2400 + 2xTF7100HDPVRtPlus + SKIPPA [RIP] + T2 + U4 + V2
No IceTV: a few Toppys and T2
Synology NAS
Check out the oztoppy wiki and oztoppy Forum for Toppy help

Ian_AW

Quote from: IanL-S on November 26, 2024, 04:52:29 PMNot sure about the sound problem, but @Danial Hall says the way to fix the LCN numbers is to watch live TV on one "channel" from each network that has incorrect LCN for a couple of minutes and the LCNs correct themselves. I have tried it and it works a treat.
Ian

Thanks for that. Fingers crossed that has resolved things. Still a couple of quirks, but I will leave well enough alone.

I disabled LCN 93 and enabled LCN 99 in my IceTV account before these changes, but after getting things working, Go HD shows up as LCN 93 and there is no LCN 99 on my IceBox. And yes, LCN 93 identifies as Go HD and gets program information for the EPG.

The sound thing had to do with my configuration. I have the T2 and the IceBox. They feed their video and audio signals to the TV via HDMI. The TV then outputs the audio to a sound bar via SPDIF. This way, it does not matter which device or the TV is used, the audio comes through the sound bar. The confusion was which HDMI input and the IceBox went 0 1 2, whereas the TV refers to them as 1 2 3.

Thanks again. I had these flashbacks to when I woke on Christmas morning to find I had no T2 working,

So, thanks again. Your assistance is appreciated.

Ian_AW

After the fun, there is just one setting that has been lost.

I have (had) Subtitles set to ON by default. After the soft reset, this has been lost and I cannot find where to set this back ON as default.

Any pointers appreciated.

Thanks.

vader1111

Quote from: Ian_AW on November 28, 2024, 03:26:07 PMAfter the fun, there is just one setting that has been lost.

I have (had) Subtitles set to ON by default. After the soft reset, this has been lost and I cannot find where to set this back ON as default.

Any pointers appreciated.

Thanks.
While playing a recording:
  • Click on OK or pause.
  • Use left/right to highlight the settings (cog) button.
  • Go into subtitles, and turn on.
  • Click on "use settings for all files" (or similar wording). 

Sorry, I'm at work, so I can't give you the precise instructions.

raymondjpg

Quote from: Ian_AW on November 28, 2024, 03:26:07 PMAfter the fun, there is just one setting that has been lost.

I have (had) Subtitles set to ON by default. After the soft reset, this has been lost and I cannot find where to set this back ON as default.

Any pointers appreciated.

Thanks.

There are a couple of things:

1. For Live TV, in Settings|Player|Preferred subtitle language, set to English.
2. For recordings, ensure that in TVHeadend Configuration|Recording|Digital Video Recorder Profiles that Stream profile is set to matroska. I think that is the default setting now anyway.

Then in any video window hit enter and right arow across to the fourth last icon and enable subtitles and set as default for all media.


Beyonwiz T2, Beyonwiz U4, IceBox BYO with Hauppauge WinTV-dualHD (x2), Hauppauge WinTV-quadHD

Ian_AW

Quote from: raymondjpg on November 28, 2024, 04:44:13 PM
Quote from: Ian_AW on November 28, 2024, 03:26:07 PMAfter the fun, there is just one setting that has been lost.

I have (had) Subtitles set to ON by default. After the soft reset, this has been lost and I cannot find where to set this back ON as default.

Any pointers appreciated.

Thanks.

There are a couple of things:

1. For Live TV, in Settings|Player|Preferred subtitle language, set to English.
2. For recordings, ensure that in TVHeadend Configuration|Recording|Digital Video Recorder Profiles that Stream profile is set to matroska. I think that is the default setting now anyway.

Then in any video window hit enter and right arow across to the fourth last icon and enable subtitles and set as default for all media.



This seems to have done it.

Thanks everyone.